Steel Castings for Sirohi and Abu Road Buyers: Grades, Tests and RFQ Guide

Steel castings for Sirohi and Abu Road buyers are usually ordered in IS 1030 carbon steel grades such as 230-450W, or in alloy steel when the part faces wear, impact or heat. Alloynex Foundries, Jaipur, makes both to your drawing and serves the whole Sirohi district.

Last updated: 14 November 2026

This guide is for engineers, maintenance heads and buyers in Sirohi, Abu Road, Pindwara, Sheoganj and Reodar. It explains which steel casting grade to pick, how carbon steel compares with alloy steel, which tests to ask for, and how to send an enquiry that gets a clear answer the first time.

Why do Sirohi and Abu Road plants need steel castings?

Industry in Sirohi district includes stone cutting and processing, mineral grinding, cement-related work, pumps, and general engineering workshops. These plants run machines that see shock, wear and heavy loads. Grey iron cracks under such impact. Steel castings bend before they break, and they can be weld repaired when the grade allows it.

Common steel cast parts in the district are machine frames, levers, brackets, gear blanks, crusher and grinder wear parts, valve bodies, flanges and pump parts. Most are made to a drawing, in small to medium lots.

Which steel casting grade should you order?

For general parts, carbon steel to IS 1030 is the usual start. The grade name gives the minimum yield and tensile strength in MPa. The letter W means the grade is meant for welding; N means normal use. The table below is general education; always take final values from the standard.

GradeTypeMin. yield / tensile (MPa)Typical Sirohi and Abu Road parts
IS 1030 200-400WCarbon steel200 / 400Brackets, levers, light covers
IS 1030 230-450WCarbon steel230 / 450Machine parts, flanges, housings
IS 1030 280-520WCarbon steel280 / 520Gear blanks, heavier brackets
IS 1030 340-570WCarbon steel340 / 570Highly loaded parts
ASTM A216 WCBCarbon steelAs per standardValve and pump bodies
IS 276 high manganese steelAlloy steelAs per standardCrusher and grinder wear parts
ASTM A217 WC6Cr-Mo alloy steelAs per standardValves and parts in hot service

Read the full grade table in our guide to IS 1030 steel casting grades.

Carbon steel vs alloy steel castings: which one fits?

PointCarbon steel (IS 1030)Alloy steel
Main strengthToughness and weldabilityWear, impact or heat resistance
Usual heat treatmentNormalised, or normalised and temperedQuenched and tempered, or water toughened for manganese steel
MachiningGoodHarder grades are slower to machine
Typical useFrames, flanges, housings, leversCrusher liners, grinder parts, hot-service valves
When to chooseNormal loads and temperaturesAbrasion, heavy impact or high temperature

Simple rule: start with carbon steel and move to alloy steel only when wear, impact or heat demands it. Our guide on steel vs alloy steel castings explains this in more depth.

Which tests and certificates should you ask for?

Tests prove the grade. Ask for them in the enquiry, not after delivery. A typical plan for steel castings includes:

  • Chemical analysis of each heat
  • Tensile strength, yield and elongation on a test sample
  • Hardness on the part or test bar
  • Heat treatment condition, such as normalised, named on the certificate
  • Dimensional report against your drawing
  • Impact test, only if your drawing or standard asks for it
  • An EN 10204 3.1 certificate linked to the heat number

See EN 10204 test certificates explained and normalizing vs annealing steel castings for what to write.

How to send a steel casting enquiry from Sirohi or Abu Road

  1. Share a drawing with tolerances, or a 3D model if you have one.
  2. Name the grade and standard, such as IS 1030 230-450W.
  3. State the heat treatment condition you need.
  4. Mark machined faces and datums, and say if you need machining.
  5. Give the yearly quantity and lot size.
  6. List the tests and the certificate type.
  7. Send it to info@alloynex.com for a technical review.

Common mistakes when ordering steel castings

  • Writing only “MS casting” or “steel casting” with no grade.
  • Not stating the heat treatment, so the part is supplied in an unknown condition.
  • Choosing an alloy grade when carbon steel is enough, which adds machining time.
  • Asking for impact tests without a temperature or value.
  • Skipping sample approval before the first lot.

Service area: Sirohi district and nearby

Alloynex Foundries supplies steel and alloy steel castings from Harmada, Jaipur, to buyers in Sirohi, Abu Road, Pindwara, Sheoganj, Reodar and Mount Abu, and to nearby Jalore and Pali. For alloy steel parts near Ajmer, see alloy steel castings for Kishangarh and Ajmer. We work to ISO 9001, ISO 14001 and ISO 45001 management systems.

FAQs

Who supplies steel castings to buyers in Sirohi and Abu Road?

Alloynex Foundries, Jaipur, makes carbon steel and alloy steel castings to customer drawings and serves buyers across Rajasthan, including Sirohi, Abu Road, Pindwara and Sheoganj. Send your drawing to info@alloynex.com for a technical review.

Which IS 1030 grade is most common for machine parts?

IS 1030 grade 230-450W is a common choice for general machine parts, flanges and housings. It gives at least 230 MPa yield and 450 MPa tensile strength, and the W grades are meant for welding.

When should I choose alloy steel instead of carbon steel castings?

Choose alloy steel when the part must resist abrasion and impact, hold strength at high temperature, or reach high hardness after quench and temper. For general loads, carbon steel castings are usually enough.

Which certificate should come with steel castings?

Most buyers ask for an EN 10204 3.1 certificate that shows chemistry, tensile, elongation and hardness results, linked to the heat number and the heat treatment condition.

सिरोही और आबू रोड में स्टील कास्टिंग कौन सप्लाई करता है?

एलॉयनेक्स फाउंड्रीज़, जयपुर, ड्रॉइंग के अनुसार कार्बन स्टील और अलॉय स्टील कास्टिंग बनाती है और सिरोही, आबू रोड, पिंडवाड़ा और शिवगंज के खरीदारों को सप्लाई करती है। ड्रॉइंग info@alloynex.com पर भेजें।

स्टील कास्टिंग के लिए ड्रॉइंग पर क्या लिखें?

ग्रेड और स्टैंडर्ड (जैसे IS 1030 230-450W), हीट ट्रीटमेंट कंडीशन (जैसे नॉर्मलाइज़्ड), मशीनिंग वाली सतहें, ज़रूरी टेस्ट और EN 10204 3.1 सर्टिफिकेट लिखें।

Send your drawing for a technical review

Planning a new steel cast part, or a second source for an existing one in Sirohi or Abu Road? Send your drawing for a technical review, or request a metallurgy consultation. Email info@alloynex.com. Alloynex Foundries, P. No. 17, Bheruji Nagar, Road No. 14, Harmada, Jaipur, Rajasthan 302013.

Related: steel and alloy steel castings for Sikar and Beawar buyers and grey and SG iron castings for Pali buyers

Worked example: specifying a steel casting for an Abu Road plant

Short answer: for a steel cast part in Sirohi or Abu Road that takes shock and will be welded, specify IS 1030 grade 230-450W, normalized, with chemistry, tensile, elongation and hardness results on an EN 10204 3.1 certificate. The worked example below shows how a buyer gets to that line on the drawing.

The case: a stone-processing unit near Abu Road needs a new lever arm for a cutting machine. The old part cracked near a weld. It sees repeated shock, is welded to a bracket on site, and has two bored holes.

StepQuestionAnswer for this partResult on the drawing
1What load does it see?Repeated shock, medium stressCarbon steel casting, not cast iron
2Will it be welded?Yes, to a bracket on siteA W grade: IS 1030 230-450W
3Does it face wear or heat?NoNo need for alloy steel
4Which heat treatment?Even grain for toughnessNormalized
5Which surfaces are machined?Two bores and one faceMark them; add machining allowance (ISO 8062-3 RMA)
6What proof is needed?Grade and condition must be traceableEN 10204 3.1 with heat number

Final drawing note: “Material: IS 1030 230-450W steel casting, normalized. Tests: chemical analysis, tensile, elongation, hardness. Certificate: EN 10204 3.1 linked to heat number. Machined faces as marked.”

Why the old part cracked is also worth checking: a non-weldable grade, or welding without care for heat input, often causes cracks next to the weld. Naming a W grade on the drawing removes that risk at the source. See IS 1030 steel casting grades and machining allowance on castings.

Have a similar part in Sirohi, Abu Road, Pindwara or Sheoganj? Send your drawing for a technical review to info@alloynex.com.

Last updated: 15 November 2026

Steel castings for Sirohi and Abu Road: a QAP-style inspection plan

A quality assurance plan (QAP) lists each check on a steel casting, when it is done, who witnesses it and which record proves it. For IS 1030 steel castings ordered from Sirohi, Abu Road or Pindwara, agree the QAP before the pattern is made, so every lot arrives with the same proof.

Last updated: 16 Nov 2026

StageCheckAcceptance basisRecordBuyer role
1. Drawing reviewGrade, heat treatment, machined faces, tolerance gradeDrawing and IS 1030 grade, e.g. 230-450WAgreed drawing revisionApprove
2. MeltingChemical analysis per heatIS 1030 limits for the gradeSpectro report with heat numberReview
3. Heat treatmentNormalizing or normalize and temperCondition named on drawingFurnace chart or logReview
4. Mechanical testTensile, yield, elongation on test barGrade minimums, e.g. 230 MPa yield and 450 MPa tensileTest reportReview or witness
5. Visual and dimensionalSurface, cracks, key sizesISO 8062-3 DCTG grade on drawingDimensional reportWitness first article
6. NDT (if specified)MPI on edges, UT on thick sectionsLevel stated on drawingNDT reportWitness if critical
7. DispatchMarking, heat number, packingOrder and QAPEN 10204 3.1 certificateReceive and file

Fact: the two numbers in an IS 1030 grade are the minimum yield and tensile strength in MPa; the letter W marks a grade with chemistry controlled for welding.

Tip: if a part is safety-critical, mark stage 4 and stage 6 as witness points and give the foundry two working days notice of your visit.

Related: FG 260 grey iron castings for Sikar buyers · marble machinery castings in Kishangarh · ISO 8062-3 tolerances

Send your drawing for a technical review with your QAP or ask for one to be drafted: info@alloynex.com.

Related: cement plant wear-part castings for Beawar