EN 10204 Test Certificates: 2.1, 2.2, 3.1 and 3.2 Explained for Buyers

A casting, a pipe or a fitting arrives with a sheet of paper. That paper decides whether your QA team accepts the lot, whether your customer accepts your assembly, and whether an inspector signs off a pressure system. Most of the time the paper is an EN 10204 certificate. But “3.1” on a purchase order and “3.1” on a delivered certificate do not always mean the same thing.

This guide explains the four EN 10204 types in simple words, what each one proves, who must sign it, and how to check it against the part in your hand.

What is EN 10204?

EN 10204 (current edition 2004) is a European standard. It does not set any test, grade or limit. It only defines types of inspection documents for metallic products – who checks, what is reported and who signs. It is used across the world, including India, the Middle East and the Americas, for castings, forgings, plates, bars, tubes, pipes and fittings. ISO 10474 covers the same idea.

So a certificate always has two parts working together:

  1. The material standard on the order (for example IS 1865, EN 1563, ASTM A216 WCB, IS 2062, ASTM A106, ASTM A234 WPB). This says what must be tested and what values must be met.
  2. The EN 10204 type. This says how the results are proven and who stands behind them.

The four types at a glance

TypeNameTest results shown?Based onSigned (validated) by
2.1Declaration of compliance with the orderNoManufacturer’s statementManufacturer
2.2Test reportYes – non-specificTests on regular production, not necessarily this lotManufacturer
3.1Inspection certificate 3.1Yes – specificTests on the actual products delivered (or their test unit)Manufacturer’s authorised inspection representative, independent of the production department
3.2Inspection certificate 3.2Yes – specificTests on the actual products deliveredManufacturer’s independent inspection representative and the purchaser’s representative or an inspector named by regulations

Specific vs non-specific inspection – the key difference

Non-specific inspection means the manufacturer reports typical results from its normal production of the same grade and process. The values are real, but they may not come from your heat or your batch. This is type 2.2.

Specific inspection means the tests were done on the products being delivered, or on the test unit (for example the heat or the heat-treatment batch) that those products belong to. This is type 3.1 and 3.2. Only specific inspection links the numbers to the exact metal you receive.

For a pressure-holding valve body, a pump casing or a pipe going into a process plant, that link is usually what the end customer wants.

Type 2.1 and 2.2: when are they enough?

  • 2.1 is a simple statement: “the product meets the order.” No numbers. It suits non-critical items where the grade is not safety-relevant.
  • 2.2 adds typical test results. It is common for general engineering steel, structural sections and non-pressure parts.

If your drawing lists a grade but your customer does not ask for heat-wise proof, 2.2 may be enough. Decide this at enquiry stage, not after delivery.

Type 3.1: the most common requirement

A 3.1 certificate shows results from tests on the delivered product’s test unit, and it is signed by an inspection person who does not report to production. That independence is the whole point – the person approving the results is not the person trying to dispatch the lot.

A good 3.1 for a casting or pipe normally carries:

  • Manufacturer name and certificate number
  • Purchaser, order number and item reference
  • Product description, size and quantity
  • Material standard and grade, with edition where required
  • Heat number (and heat-treatment batch, if relevant)
  • Chemical analysis of the heat (ladle or product analysis)
  • Mechanical test results: tensile strength, yield strength, elongation; hardness and impact energy if the standard or order asks
  • Heat-treatment condition (for example normalised, quenched and tempered)
  • Other tests the order asks for (dimensional check, visual check, hydro test, NDT) with the result
  • A clear statement that the product complies with the order
  • Name, function and signature of the authorised inspection representative, with date

In European pressure-equipment work, materials for main pressure-bearing parts are usually expected to come with certification based on specific product control – in practice this is very often a 3.1.

Type 3.2: when a second signature is needed

A 3.2 has the same content as a 3.1, but a second party must also witness and sign: the buyer’s own inspector, or a third-party inspection agency named by the buyer or by regulation. It takes planning – the inspector must be present for the tests or must review them – so it should be agreed at order stage with the inspection points written into the quality plan.

3.2 is typical for oil and gas, power and some export projects where the end client names its inspection agency.

Old names you may still see (EN 10204:1991)

Some drawings and old specifications still use 1991 names:

Old (1991)Use today (2004)
2.3 (specific test report)Withdrawn – usually replaced by 3.1
3.1.B3.1
3.1.A, 3.1.C, 3.23.2

If an old drawing says “3.1.B”, ask for 3.1. If it says “3.1.C”, the intent was a buyer-witnessed certificate, so plan for 3.2.

Heat traceability: how to check the paper against the part

A certificate is only useful if you can prove the part came from that heat. Before you accept a lot:

  1. Find the heat number on the part. On castings it is usually cast-in or stamped; on pipes and fittings it is stencilled or stamped.
  2. Match it to the certificate. Same heat number, same grade, same size range.
  3. Check the values against the standard, not just “OK”. A tensile result is only meaningful next to the grade’s minimum.
  4. Check the heat-treatment condition. For SG iron, steel and alloy steel castings, the properties depend on it. See our guide to heat treatment of castings.
  5. Check the signature and function. For 3.1, the signer must be from inspection, not production.
  6. Check the date order. Tests should come before the certificate date, and the certificate before dispatch.

Weak traceability is the most common reason a good part gets rejected at the customer’s goods-in.

Common mistakes buyers make

  • Writing only “MTC required” on the PO, without the EN 10204 type.
  • Ordering 3.2 without naming the inspection agency, which delays dispatch.
  • Asking for 3.1 but not listing the extra tests needed (impact test, hardness, hydro test). A 3.1 only reports what the order and standard ask for.
  • Accepting a certificate that shows a different edition of the material standard.
  • Accepting a distributor’s re-typed certificate when the original is needed. Ask for the original or a properly traceable copy.

What to write on your enquiry or purchase order

To avoid back-and-forth, give the supplier one clear line per part:

  • Material standard and grade, with edition (for example “EN-GJS-400-15 to EN 1563”)
  • Certificate type (for example “EN 10204 3.1”)
  • Tests to be reported (chemistry, tensile, hardness, impact at a stated temperature, other)
  • Heat-treatment condition
  • Marking needed on the part (heat number, grade, your part number)
  • Third-party inspection agency, if 3.2

Send these details with your drawing to info@alloynex.com and our team will review them before quoting the technical route.

How we handle this at Alloynex

Alloynex works under an ISO 9001 quality system. Tell us at the drawing review stage which certificate type and tests your customer or regulator needs, and we will confirm the testing and documentation route in writing before production starts.

Send your drawing for a technical review – share the grade, quantity and certificate requirement at info@alloynex.com or through our enquiry form.

Frequently asked questions

What is the difference between a 2.2 and a 3.1 certificate?

A 2.2 shows typical results from the manufacturer’s normal production and is signed by the manufacturer. A 3.1 shows results from tests on the actual products delivered and is signed by an inspection representative who is independent of production.

Is a mill test certificate the same as a 3.1?

Not always. “Mill test certificate” or “MTC” is a general name. It can be a 2.2, a 3.1 or something else. Check which EN 10204 type is printed on it.

Who signs a 3.2 certificate?

Both the manufacturer’s authorised inspection representative and the purchaser’s representative or an inspector designated by official regulations.

Does EN 10204 say which tests to do?

No. The tests and limits come from the material standard and your order. EN 10204 only defines the type of document and who validates it.

What does 3.1.B mean today?

3.1.B is the 1991 name. In EN 10204:2004 it is simply 3.1.

Why does the heat number matter?

It is the only link between the certificate and the part. Without a matching heat number, the test results cannot be proven to belong to the product you received.

Related reading

What does an EN 10204 3.1 certificate mean?

Short answer: an EN 10204 3.1 certificate is an inspection certificate in which the manufacturer declares that the delivered products meet the order, and shows test results from the actual heat or batch supplied. It is signed by the manufacturer’s authorised inspection person, who is independent of production. No outside inspector signs a 3.1.

QuestionEN 10204 3.1 answer
Whose tests?The manufacturer’s own tests on the delivered heat, batch or test unit
Specific or typical results?Specific: linked to your material by heat number
Who signs?Manufacturer’s inspection representative, not from production
Third-party witness?No (that is type 3.2)
Which tests appear?Only those the material standard and your order ask for
Old 1991 name3.1.B

How to read a material test certificate for castings: 7 checks

Read a casting test certificate from top to bottom in this order. It takes a few minutes and catches most problems before the lot reaches your machine shop.

  1. Certificate type: look for “EN 10204 3.1” (or 2.2 / 3.2) printed on the sheet, matching your purchase order.
  2. Order and part link: your PO number, part number, drawing revision and quantity.
  3. Grade and standard: for example IS 210 FG 260, IS 1865 SG 500/7, ASTM A536 65-45-12 or IS 1030 grade, with the edition if your order states one.
  4. Heat number: the same number must be cast-in or stamped on the parts.
  5. Chemistry: compare C, Si, Mn, S and P (plus Cr, Ni, Mo for alloy steel, and residual Mg for SG iron) with the limits you agreed.
  6. Mechanical results vs minimums: tensile strength, elongation and hardness; for SG iron also nodularity from the microstructure check; for steel also yield and impact if ordered.
  7. Heat treatment, signature and dates: condition (as-cast, annealed, normalised, quenched and tempered), the inspector’s name and function, and test dates before the certificate date.

Glossary: terms you will see on a casting certificate

TermWhat it means for the buyer
Heat numberID of one melt of metal; links the paper to the part
Ladle analysisChemistry taken from the molten metal before pouring
Separately cast test barTest sample poured from the same heat, used for tensile tests on iron grades
UTS / tensile strengthLoad at break per area, in N/mm² or MPa; must meet the grade minimum
Elongation (%)How much the test bar stretches before it breaks; key for SG iron and steel
BHNBrinell hardness number; linked to strength and machinability
Nodularity (%)Share of round graphite in SG iron; low nodularity means lower strength and ductility
ConditionHeat-treatment state of the parts when tested

What does EN 10204 3.1 mean in simple words?

It means “we tested the metal you are getting, and an inspector who does not work for production signed the results”. The numbers belong to your heat, not to typical production.

What should a test certificate for SG iron castings show?

Grade (for example IS 1865 SG 500/7), heat number, chemistry, tensile strength, elongation, hardness, nodularity from the microstructure check, the heat-treatment condition, and the signature of the inspection person.

EN 10204 3.1 सर्टिफिकेट का क्या मतलब है?

3.1 सर्टिफिकेट में निर्माता लिखता है कि भेजा गया माल ऑर्डर के अनुसार है, और उसी हीट या बैच के असली टेस्ट रिज़ल्ट देता है। इस पर प्रोडक्शन से अलग निरीक्षण अधिकारी के हस्ताक्षर होते हैं। तीसरे पक्ष का निरीक्षण चाहिए तो 3.2 माँगें।

For buyers in Rajasthan and beyond: Alloynex Foundries, Harmada, Jaipur, supplies grey iron, SG iron, steel and alloy steel castings with test certificates to buyers in Jaipur, Jodhpur, Udaipur, Kota, Ajmer, Bhilwara, Alwar, Bhiwadi, Neemrana and Sikar, across India and for export. Tell us the certificate type and tests at enquiry stage: info@alloynex.com. Request a metallurgy consultation.

Related: machining allowance on castings, SG iron vs grey cast iron, castings buyer guide for Rajasthan, our casting services.

Last updated: 13 November 2026

EN 10204 3.1 vs 3.2: which one should you order, and how do you read the mill test certificate?

Direct answer: order EN 10204 3.1 when the manufacturer’s own independent inspector may certify specific test results for your heat; order 3.2 when your customer, a regulator or a named third-party agency must also witness the tests and co-sign. Read the mill test certificate by matching type, order, grade, heat number, chemistry, mechanical results and signature.

Decision matrix: 3.1 or 3.2?

Your situationOrderReason
Normal engineering castings, pipes or fittings; your QA checks the paper3.1Specific results with independent in-house sign-off are enough
End client names a third-party inspection agency in its specification3.2The agency must witness and co-sign
Pressure-retaining part where a notified body or regulator must sign3.2Second validation is required by rule
Old drawing says 3.1.B3.13.1.B is the 1991 name for 3.1
Old drawing says 3.1.C or 3.1.A3.2These 1991 types needed buyer or official witness
Grade not safety-relevant and no heat proof asked2.2Typical results are enough; decide at enquiry

Spec checklist: what a casting MTC must show, with example limits

FieldWhat to checkExample (minimum values)
Certificate typeEN 10204 type printed, same as PO3.1
Grade and standardGrade and edition match the drawingIS 1865 SG 500/7
Heat numberSame number cast-in or stamped on the partsHeat-wise traceable
Tensile strengthResult at or above grade minimumSG 500/7: 500 MPa; SG 400/15: 400 MPa; FG 260: 260 MPa
0.2% proof stressAt or above minimum (SG iron, steel)SG 500/7: 320 MPa; SG 400/15: 250 MPa
ElongationAt or above minimumSG 500/7: 7%; SG 400/15: 15%
HardnessWithin the range on the orderBHN range as agreed
MicrostructureNodularity for SG iron, as agreed on orderNodularity % reported
Heat treatmentCondition statedAs-cast, annealed, normalised, Q&T
Signature3.1: inspection person independent of production; 3.2: plus second partyName, function, date

Example values are minimum tensile figures from the named Indian grades (IS 1865, IS 210). Your own order and standard edition always govern.

How to read a mill test certificate in 6 steps

  1. Check the EN 10204 type against your purchase order.
  2. Check the purchase order number, part number, drawing revision and quantity.
  3. Match the heat number on the paper with the heat number on the parts.
  4. Compare each chemical element with the limits in the standard or order.
  5. Compare each mechanical result with the grade minimum, not just “OK”.
  6. Check heat-treatment condition, signer’s function and that test dates come before the certificate date.

EN 10204 3.1 vs 3.2 FAQs (English and Hindi)

Can a supplier upgrade a 3.1 to a 3.2 after dispatch?

No. A 3.2 needs the second party to witness or review the tests, so it must be planned before testing.

Does a 3.2 certificate mean better material?

No. The material and tests can be the same. A 3.2 adds a second, independent validation.

EN 10204 3.1 और 3.2 में क्या अंतर है?

3.1 पर केवल निर्माता के स्वतंत्र निरीक्षण अधिकारी के हस्ताक्षर होते हैं। 3.2 पर इसके साथ खरीदार या तीसरे पक्ष के इंस्पेक्टर के भी हस्ताक्षर होते हैं।

मिल टेस्ट सर्टिफिकेट कैसे पढ़ें?

सर्टिफिकेट का प्रकार, ऑर्डर नंबर, ग्रेड, हीट नंबर, केमिस्ट्री, टेंसाइल और एलॉन्गेशन के मान, हीट ट्रीटमेंट और हस्ताक्षर को अपने ऑर्डर और स्टैंडर्ड से मिलाएँ।

Alloynex Foundries, Harmada, Jaipur, makes grey iron, SG iron, steel and alloy steel castings to customer drawings for buyers in Jaipur, Jodhpur, Udaipur, Kota, Ajmer, Bhilwara, Alwar, Bhiwadi, Neemrana and Sikar, across India and for export. Tell us the certificate type and tests at enquiry stage and send your drawing for a technical review (info@alloynex.com). Related: ISO 8062-3 casting tolerances, our casting services.

Last updated: 13 November 2026

EN 10204 2.2 vs 3.1 for castings: which one does your part need?

Direct answer: a 2.2 test report shows typical results from the maker’s normal production, signed by the maker. A 3.1 inspection certificate shows results from the actual heat or batch delivered, signed by an inspector independent of production. For pump casings, valve bodies and other pressure or safety parts, order 3.1.

PointEN 10204 2.2EN 10204 3.1
Results shownTypical, from regular productionSpecific, from your heat or test unit
Link to the partsNo heat-wise link requiredHeat number on paper and on part
Signed byManufacturerManufacturer’s inspection person, not from production
Good forNon-critical covers, brackets, general structural itemsPressure parts, safety parts, export and OEM supply
Order wording“EN 10204 2.2 test report”“EN 10204 3.1 inspection certificate”

Annotated example: what each field on a 3.1 casting certificate tells you

The layout below is an illustrative example of a 3.1 certificate for one SG iron lot. Field names vary by supplier, but a complete certificate covers each line.

Field on the certificateExample entry (illustrative)What the buyer checks
Certificate typeEN 10204 3.1Same type as the purchase order
Material and standardIS 1865 SG 500/7Grade and edition match the drawing
Heat numberHeat ID as cast on the partSame ID on every part in the lot
ChemistryC, Si, Mn, S, P, residual MgWithin agreed limits
Tensile strengthResult in MPaNot below 500 MPa for SG 500/7
0.2% proof stressResult in MPaNot below 320 MPa for SG 500/7
ElongationResult in %Not below 7% for SG 500/7
HardnessResult in BHNInside the range on the order
MicrostructureNodularity % reportedMeets the value agreed on the order
ConditionAs-cast or heat treatedMatches the drawing
Declaration and signatureName, function, dateSigner is from inspection, not production

Red flags on a casting certificate: 5 checks before you accept a lot

  1. The type printed on the sheet is different from the type on your order.
  2. The heat number on the paper does not match the number cast-in or stamped on the parts.
  3. Results are written only as “OK” or “Satisfactory” with no numbers.
  4. Test dates come after the certificate date or after dispatch.
  5. The signer’s function is production or dispatch, not inspection.

EN 10204 2.2 और 3.1 में क्या अंतर है?

2.2 में निर्माता की सामान्य प्रोडक्शन के टिपिकल रिज़ल्ट होते हैं। 3.1 में आपको भेजी गई उसी हीट के असली टेस्ट रिज़ल्ट होते हैं और प्रोडक्शन से अलग निरीक्षण अधिकारी हस्ताक्षर करता है। प्रेशर और सेफ्टी पार्ट्स के लिए 3.1 माँगें।

Alloynex Foundries, Harmada, Jaipur, supplies grey iron, SG iron, steel and alloy steel castings, tubes, pipes and fittings with heat-wise test certificates to buyers across Rajasthan, India and for export. Send your drawing for a technical review at info@alloynex.com. Related: IS 1239 vs IS 3589 pipe, SG iron grades and IS 1865.

Last updated: 14 November 2026

Which tests should a 3.1 certificate show for grey iron, SG iron and steel castings?

Last updated: 14 November 2026

Short answer: EN 10204 sets the type of certificate, not the tests. The tests come from the material standard. A 3.1 for grey iron (IS 210) shows chemistry, tensile and hardness. SG iron (IS 1865) adds elongation, proof stress and nodularity. Steel castings (IS 1030) add yield, elongation and heat treatment condition.

Test-by-material matrix for casting certificates

Item on the certificateGrey iron (IS 210)SG iron (IS 1865)Carbon steel (IS 1030)Alloy steel (Cr-Mo)
Chemical analysisYes (C, Si, Mn, S, P)Yes (plus Mg)Yes (C, Mn, Si, S, P)Yes (plus Cr, Mo, Ni)
Tensile strengthYesYesYesYes
Yield or 0.2% proof stressNoYesYesYes
ElongationNoYesYesYes
Hardness (HB)UsualUsualIf orderedUsual
Microstructure / nodularityIf orderedUsualNoIf ordered
Impact testNoOnly for low-temperature gradesIf orderedIf ordered
Heat treatment conditionIf stress relievedIf annealed or normalizedYes (e.g. normalized)Yes (e.g. quenched and tempered)

“Usual” means most buyers ask for it. “If ordered” means it appears only when your purchase order or drawing asks for it. The certificate type (2.2, 3.1 or 3.2) only decides who checks and signs the results.

Copy-ready purchase order lines

GREY IRON:  Casting to IS 210 FG 260. Certificate EN 10204 3.1 with chemistry, tensile and hardness per heat.
SG IRON:    Casting to IS 1865 SG 500/7. Certificate EN 10204 3.1 with chemistry, tensile, 0.2% proof, elongation, hardness and nodularity per heat.
STEEL:      Casting to IS 1030 Gr 280-520W, normalized. Certificate EN 10204 3.1 with chemistry, yield, tensile, elongation and heat treatment record per heat.

Quick facts

  • EN 10204 names four document types: 2.1, 2.2, 3.1 and 3.2.
  • A 3.1 certificate is signed by the maker’s inspection staff who are independent of production.
  • A 3.2 certificate is also signed by the buyer’s inspector or a third party.
  • Grey iron grades under IS 210 are set by tensile strength only, so no elongation value is shown.

कास्टिंग के 3.1 सर्टिफिकेट में कौन से टेस्ट होने चाहिए?

ग्रे आयरन (IS 210) के लिए केमिस्ट्री, टेन्साइल और हार्डनेस। एसजी आयरन (IS 1865) के लिए इनके साथ प्रूफ स्ट्रेस, एलॉन्गेशन और नोड्यूलैरिटी। स्टील कास्टिंग (IS 1030) के लिए यील्ड, एलॉन्गेशन और हीट ट्रीटमेंट की स्थिति भी लिखी होनी चाहिए।

Send your drawing for a technical review, or request a metallurgy consultation. Email info@alloynex.com with the grade and the tests you need on the certificate.

Related: which test certificate to ask for with seamless pipe for Barmer and Balotra lines

EN 10204 3.1 vs 3.2: what changes in the inspection plan, step by step?

Last updated: 15 November 2026

Direct answer: the tests can be the same for 3.1 and 3.2. What changes is the inspection plan. For 3.1, the maker’s independent inspector checks and signs. For 3.2, you also fix hold points where your inspector or a named agency must witness, review and co-sign. Plan these points at order stage.

Witness plan sheet: 3.1 vs 3.2 for a casting order

Stage3.1: who acts3.2: who actsRecord
Order reviewMaker confirms grade and testsMaker + buyer name the agencyQuality plan with hold points
Melting and pouringMaker records heat numberAgency may review heat recordsHeat log
Test bar and chemistryMaker’s lab testsAgency witnesses or reviews testsLab report
Heat treatmentMaker records cycleAgency reviews chart if askedHeat treatment chart
Visual and dimensionalMaker inspectsAgency witnesses at hold pointDimensional report
CertificateMaker’s inspector signsMaker’s inspector + agency signEN 10204 3.1 or 3.2
  1. Decide 3.1 or 3.2 before you send the enquiry.
  2. For 3.2, name the agency and its contact on the PO.
  3. Agree hold points and notice days in the quality plan.
  4. Keep the heat number on every part and every report.
  5. Accept the lot only when the signed certificate matches the parts.

When must a 3.2 inspector be called?

Before the tests are done. The buyer or named agency must witness or review tests at agreed hold points, so the dates go into the quality plan at order stage.

3.2 सर्टिफिकेट के लिए इंस्पेक्टर कब बुलाएँ?

टेस्ट से पहले। ऑर्डर के समय ही क्वालिटी प्लान में होल्ड पॉइंट तय करें, ताकि इंस्पेक्टर टेस्ट देख सके और साइन कर सके।

Send your drawing for a technical review or request a metallurgy consultation: info@alloynex.com.

EN 10204 3.1 vs 3.2 for castings: 6 myths and the facts

Short answer: A 3.1 and a 3.2 certificate report the same kind of results: tests on the actual castings supplied or their test units. The only difference is who signs. A 3.1 is validated by the foundry’s inspection representative, independent of production; a 3.2 adds the purchaser’s inspector or an inspector named by regulations.

MythFact
A 3.2 means better material.The grade and tests are the same; 3.2 adds an outside witness.
A 2.2 is the same as a 3.1.A 2.2 can show typical results, not results from your castings.
The steel mill’s certificate covers my casting.A casting is re-melted; the foundry’s own heat results are needed.
Any supplier can sign a 3.1.It must be the manufacturer’s authorised inspection representative.
A 3.2 can be added after dispatch.The witness must be present when tests are done, so plan it at order stage.
The certificate alone proves the part.Only if the heat number on paper matches the mark on the casting.

Worked example: one SG iron order, two certificate paths

  1. Drawing says “SG 500/7 to IS 1865, EN 10204 3.1”.
  2. The foundry pours the heat with a test bar and records the heat number on each casting.
  3. Chemistry and tensile results from that heat go on the 3.1, signed by the foundry’s inspection representative.
  4. If the order says 3.2, the buyer’s inspector is called before the test bar is pulled, and also signs.

FAQs

Is an EN 10204 3.2 certificate better material than 3.1?

No. Both report tests on the products supplied. A 3.2 only adds a second signature from the purchaser’s inspector or an inspector named by regulations.

Can a trader issue a 3.1 certificate?

Under EN 10204 an intermediary passes on the manufacturer’s original document or a copy without change. A 3.1 should come from the foundry or mill that made and tested the product.

3.1 और 3.2 सर्टिफिकेट में असली फर्क क्या है?

दोनों में सप्लाई किए गए माल के टेस्ट रिज़ल्ट होते हैं। 3.2 में निर्माता के इंस्पेक्टर के साथ खरीदार या अधिकृत इंस्पेक्टर का दूसरा हस्ताक्षर होता है।

क्या 3.2 लेने से माल बेहतर हो जाता है?

नहीं। ग्रेड और टेस्ट वही रहते हैं; 3.2 सिर्फ बाहरी गवाह जोड़ता है। ज़रूरत होने पर ही 3.2 मांगें।

Send your drawing for a technical review to info@alloynex.com with the grade, weight per piece, yearly quantity and the tests you need.

Last updated: 15 November 2026

EN 10204 quick answers for casting buyers

Short answer: type 3.1 is signed by the maker’s own inspection person, independent of production; type 3.2 is signed by both the maker’s inspector and a third party or the buyer’s inspector. Most castings need 3.1; ask for 3.2 only when your code or customer asks for witness testing.

  • Is 2.2 enough for a pump casing? Only if the drawing does not ask for specific results on that lot; 2.2 gives non-specific results.
  • Does 3.1 mean third-party testing? No. 3.1 is the manufacturer’s inspection, independent of production.
  • Who arranges 3.2? The buyer names the inspector; tests are witnessed and both sign.
  • What links the certificate to a part? The heat number cast or stamped on the part.
  • Can one certificate cover two heats? Only if both heats are listed with their own results.

Related: alloy steel castings for Kishangarh and Ajmer, textile machinery castings for Bhilwara, SG iron vs grey cast iron.

Send your drawing for a technical review, or request a metallurgy consultation, at info@alloynex.com.

Last updated: 16 Nov 2026

Related: Casting glossary in English and Hindi