Common Casting Defects and How Foundries Prevent Them

Quick answer: The seven most common casting defects are gas porosity, shrinkage cavities, sand inclusions, cold shuts, misruns, hot tears and dimensional errors. Each one is prevented at a known step: dry, vented moulds; correctly placed feeders; clean metal; the right pouring temperature; fillets and even walls; and a first-article dimensional check.

This guide explains common casting defects in simple words. For each defect you will see what it looks like, why it happens and how foundries prevent it. It is written for OEM engineers, QA teams and buyers who want to ask better questions before they place an order.

Why Casting Defects Matter

A defect can reduce strength, cause leaks, fail machining or fail a customer test. Some defects are on the surface and easy to see. Others are hidden inside and show up only during machining, pressure testing or in service.

Preventing defects is always better than finding them later. It saves time, protects your delivery plan and lowers the total cost of ownership of the part.

How do you identify a casting defect by what you see?

  1. You see round, smooth holes, often near the top surface: it is gas porosity. Likely cause: moisture, damp sand, poor venting or gas dissolved in the metal.
  2. You see rough, jagged holes in thick sections: it is a shrinkage cavity. Likely cause: poor feeding as the metal cools and shrinks.
  3. You see sand grains or pits on or inside the casting: it is a sand inclusion. Likely cause: weak mould, loose sand or sand washed by fast-flowing metal.
  4. You see a line or seam where two metal streams met: it is a cold shut. Likely cause: low pouring temperature, slow pouring or thin sections.
  5. The casting is not fully filled: it is a misrun. Likely cause: metal too cold, thin walls or poor gating.
  6. You see ragged cracks at corners or junctions: it is a hot tear. Likely cause: restrained shrinkage, sharp corners or a mould that is too hard.
  7. The size is wrong, shifted or warped: it is a dimensional error. Likely cause: pattern wear, core shift, mould shift or uneven cooling.

1. Gas Porosity

Gas porosity shows as small round holes with smooth walls. It forms when gas is trapped as the metal becomes solid.

How foundries prevent it:

  • Keep sand moisture under control and dry cores well
  • Give moulds and cores good venting
  • Use clean, dry charge material and tools
  • Control melting and pouring practice to reduce dissolved gas

2. Shrinkage Cavities

Metal shrinks as it cools. If the thick parts of a casting cannot draw liquid metal from a feeder, a rough cavity forms inside. This is common in heavy sections and at junctions.

How foundries prevent it:

  • Place risers (feeders) so they feed the thick sections last
  • Use chills to control the cooling order
  • Avoid sudden changes in wall thickness during design
  • Check designs with solidification simulation where needed

Shrinkage behaviour differs between metals. For example, SG iron and grey iron behave differently. Read more in our guide on SG iron vs grey cast iron.

3. Sand and Slag Inclusions

Inclusions are unwanted bits of sand or slag trapped in the metal. They weaken the part and can damage cutting tools during machining.

How foundries prevent it: strong, well-rammed moulds; good gating that lets metal flow smoothly; filters and slag traps in the gating system; and clean ladles.

4. Cold Shuts and Misruns

A cold shut is a seam where two streams of metal met but did not join. A misrun is a casting that did not fill completely. Both happen when metal loses heat too quickly or flows too slowly.

How foundries prevent it: correct pouring temperature, steady pouring speed, gating that fills thin sections early, and design with enough wall thickness for the metal used.

5. Hot Tears and Cracks

Hot tears are ragged cracks that form while the metal is still weak and hot. Cracks can also form later during cooling, heat treatment or fettling. Steel castings are more prone to hot tears than grey iron.

How foundries prevent it: generous fillets at corners, even wall thickness, moulds and cores that allow the casting to shrink, and controlled cooling and heat treatment. See our guide on steel vs alloy steel castings for how material choice affects this.

6. Dimensional Errors

Dimensional defects include mould shift, core shift, warping and wrong machining allowance. They lead to rejection at machining or assembly.

How foundries prevent it: well-maintained patterns and core boxes, proper core support, correct pattern allowances, and first-article dimensional checks.

Inspection and Testing Basics

Good foundries do not rely on luck. They check the process at each step and test the finished casting as agreed with the buyer. Common checks include:

  • Chemical analysis of each melt to confirm the grade
  • Mechanical tests such as tensile strength, elongation and hardness on test bars
  • Visual inspection of every casting for surface defects
  • Dimensional checks against the drawing
  • Non-destructive tests such as ultrasonic, radiography, magnetic particle or dye penetrant where the part needs it
  • Pressure or leak tests for valve bodies, pump casings and other pressure parts

Agree on the tests and acceptance levels before the first order. This removes doubt later and makes quality easy to prove.

How Buyers Can Help Prevent Defects

Many defects can be avoided before the first mould is made. As a buyer or design engineer, you can help by:

  • Sharing a clear drawing with material grade, critical surfaces and tolerances
  • Marking pressure-tight areas and machined faces
  • Keeping wall thickness as even as possible, with smooth transitions
  • Agreeing on inspection methods and acceptance levels before production
  • Asking for a first-article inspection report before regular supply begins

To learn about the casting and supply work we do, see our services page.

FAQs

What is the most common casting defect?

Gas porosity and shrinkage are among the most common casting defects. Both can usually be controlled with good venting, feeding and process control.

Can casting defects be repaired?

Some surface defects can be repaired by approved methods if the customer allows it. Critical parts often do not allow repair, so prevention is the better approach.

How are hidden defects found?

Hidden defects are found with tests such as radiography, ultrasonic testing, pressure testing or sectioning of sample parts. The right test depends on the part and its use.

Does part design affect casting defects?

Yes. Sharp corners, sudden thickness changes and isolated heavy sections make defects more likely. Small design changes can make a part much easier to cast well.

How do I check a Rajasthan foundry for casting defects?

Ask the foundry how it controls each defect before the first order: venting and dry moulds for gas porosity, feeders on thick sections for shrinkage, filters for inclusions, heat-wise chemistry for grade, and first-article inspection for dimensions. Alloynex Foundries, Jaipur, reviews every drawing for grade and tests before work starts.

DefectQuestion to ask the foundryProof to ask for
Gas porosityHow are moulds vented and dried?Process sheet, sample section
ShrinkageHow are thick sections fed?Method plan, NDT if agreed
InclusionsAre filters and slag traps used?Visual and machining check
Wrong gradeIs chemistry checked for every heat?Test certificate with heat number
Dimensional errorIs there a first-article check?Dimensional report

Read heat treatment of castings, castings buyer guide for Rajasthan and our services, or send your drawing to info@alloynex.com.

Which tests find hidden casting defects?

Radiography, ultrasonic testing, pressure testing or sectioning of sample parts find hidden defects. Agree the test and acceptance level before the first order.

Does Alloynex supply castings across Rajasthan?

Yes. Alloynex Foundries, Jaipur, supplies grey iron, SG iron, steel and alloy steel castings to buyers in Rajasthan, across India and for export.

कास्टिंग में दोष कैसे रोके जाते हैं?

अच्छी वेंटिंग, सही फीडर, फिल्टर, हर हीट की केमिस्ट्री जाँच और पहले पीस की नाप जाँच से ज़्यादातर दोष रुकते हैं। एलॉयनेक्स फाउंड्रीज़, जयपुर: info@alloynex.com

Last updated: 12 November 2026

Send Your Drawing for a Technical Review

Have a part with repeated defects, or a new design you want to cast right the first time? Share your drawing and requirements with our team for a technical review.

Send your drawing for a technical review or request a metallurgy consultation: email info@alloynex.com or visit our contact page.

Related: castings for Udaipur industry: sourcing guide for buyers

How are casting defects prevented, and which test finds each one?

Most casting defects, such as gas porosity, shrinkage, inclusions, cold shuts and hot tears, are prevented by good part design, correct gating and feeding, clean dry moulds and controlled pouring. Buyers can help by sharing the drawing early, naming the inspection method and agreeing the acceptance level before the first lot.

Defect, cause, prevention and test

DefectMain causePreventionTest that finds it
Gas porosity / blowholesMoisture or gas in mould or metalDry moulds, vents, degassingRadiography, machining check
Shrinkage cavityPoor feeding of thick sectionsRisers, chills, even wallsRadiography, ultrasonic
Sand or slag inclusionLoose sand, dirty metalClean moulds, filters, skimmingVisual, radiography
Cold shut / misrunMetal too cold or slow pourRight pouring temperature and speedVisual, dye penetrant
Hot tear / crackStress while coolingFillets, mould give, design changesMagnetic particle, dye penetrant
Dimensional errorPattern or core shiftPattern checks, core supportDimensional inspection

Numbered buyer checklist to prevent defects

  1. Share the drawing early for a design review.
  2. Mark critical areas where no defect is allowed.
  3. Name the NDT method for those areas.
  4. Agree the acceptance level in writing.
  5. Ask for first-sample inspection before the full lot.
  6. Ask for traceable heats and a test certificate.

Glossary

  • Riser: a reservoir of metal that feeds the casting as it shrinks.
  • Chill: a metal insert that cools one area faster.
  • NDT: non-destructive testing, such as radiography, ultrasonic, magnetic particle or dye penetrant.
  • Acceptance level: the agreed limit of defects allowed in an area.

What is the difference between a blowhole and a shrinkage cavity?

A blowhole is a smooth, round hole made by trapped gas. A shrinkage cavity is a rough, jagged hole made when a thick section is not fed with metal as it cools.

What is a cold shut?

A cold shut is a line or seam where two streams of metal met but did not fuse fully, usually because the metal was too cold or poured too slowly.

कास्टिंग में ब्लोहोल और श्रिंकेज में क्या फर्क है?

ब्लोहोल गैस फँसने से बना चिकना, गोल छेद होता है। श्रिंकेज मोटे हिस्से में धातु की कमी से बना खुरदरा छेद होता है। सही डिज़ाइन, राइज़र और सूखे साँचे से दोनों रोके जाते हैं। एलॉयनेक्स फाउंड्रीज़, जयपुर। ईमेल: info@alloynex.com

Related: heat treatment of castings, machining allowance on castings and cast iron foundry for Kota buyers. Send your drawing for a technical review: info@alloynex.com.

Last updated: 13 November 2026

Further reading: FG 200 vs FG 260 grey iron for Bhiwadi buyers, the castings sourcing checklist with ISO 8062-3 and EN 10204 and ductile iron castings in Jodhpur.

What causes shrinkage porosity in castings, and how is it prevented?

Direct answer: shrinkage porosity is a cluster of small, jagged voids that forms in the last part of a casting to freeze, when liquid metal can no longer reach that zone to make up for the volume lost on solidifying. It is prevented by making the casting freeze towards a correctly sized feeder, using chills at heavy sections, controlling pouring temperature and designing even wall sections.

How each metal behaves: shrinkage facts table

MetalFeeding demandWhyTypical pattern shrink allowance (linear)
Carbon and alloy steelHighNo graphite expansion; volume shrinks on freezing, so feeders must be largeabout 2%
Grey iron (for example IS 210 FG 260)LowGraphite flakes form while freezing and expand, offsetting much of the shrinkageabout 1%
SG iron (for example IS 1865 SG 500/7)MediumGraphite nodules expand late; a weak mould wall lets the casting swell and porosity forms insideabout 0.5% to 1%, set by the foundry’s own trials

Pattern allowances above are common shop-floor starting values; the foundry fixes the final figure after first-off measurement.

Prevention steps a foundry follows

  1. Find the hot spots. Compare section modulus (volume ÷ cooling surface). By Chvorinov’s rule, freezing time rises with the square of the modulus, so heavy bosses and junctions freeze last.
  2. Size the feeder. A common rule is a feeder modulus at least 1.2 times the modulus of the section it feeds, with enough liquid volume to cover that section’s shrinkage.
  3. Make freezing directional. Place feeders on the heaviest sections and chills on isolated heavy spots, so metal freezes from the far end back towards the feeder.
  4. Control gating and pouring. Hold the agreed pouring temperature and fill rate; too hot adds liquid shrinkage, too cold blocks feeding paths.
  5. Fix the design where you can. Even walls, generous fillets and no isolated heavy lumps. An inscribed-circle check at junctions shows where metal mass collects.
  6. Prove it on the first-off. Radiograph or section the first castings at the hot spots before releasing lot production.

Shrinkage porosity vs gas porosity: comparison

PointShrinkage porosityGas porosity
LookJagged, branching (dendritic) voidsRound holes with smooth, shiny walls
WhereHot spots, thick sections, under feeders, at junctionsNear the top surface, under cores, near chills that were damp
Main causeNot enough liquid feed metal while freezingGas from moisture, binders or the melt trapped as metal freezes
Main fixFeeder size and position, chills, designDry moulds and cores, venting, degassing, clean charge
Best testRadiography, sectioning, pressure testRadiography, visual after machining

How hidden shrinkage is found and graded

TestWhat it showsReference used for steel castings
Radiography (X-ray or gamma)Internal shrinkage graded by severity levelASTM E446 (up to 51 mm wall), E186 (51 to 114 mm), E280 (114 to 305 mm)
Ultrasonic testingInternal discontinuities in thick sectionsAs agreed on the order
Pressure or leak testThrough-wall porosity in pump and valve bodiesTest pressure from the drawing or product standard
SectioningExact size and spread of porosity in a sample partFirst-off approval

Agree the test method and the acceptance level on the order before the first casting. Without them, “no porosity” cannot be checked.

Shrinkage porosity FAQs (English and Hindi)

Can shrinkage porosity be removed by heat treatment?

No. Heat treatment changes structure and properties but does not close voids. The fix is in feeding, chills and design.

Why does shrinkage show only after machining?

It sits just under the skin at hot spots. When the machining allowance is cut away, the voids open on the machined face.

कास्टिंग में श्रिंकेज पोरोसिटी क्यों होती है?

जब कास्टिंग का आख़िरी जमने वाला हिस्सा फीडर से पिघली धातु नहीं ले पाता, तो वहाँ छोटे, खुरदरे छेद बन जाते हैं। मोटे सेक्शन और जोड़ों पर यह ज़्यादा होता है।

श्रिंकेज पोरोसिटी कैसे रोकें?

सही आकार का फीडर मोटे हिस्से पर लगाएँ, ज़रूरत हो तो चिल लगाएँ, पोरिंग तापमान नियंत्रित रखें और दीवार की मोटाई एक समान रखें। पहली कास्टिंग का रेडियोग्राफी से परीक्षण करें।

Alloynex Foundries, Harmada, Jaipur, makes grey iron, SG iron, steel and alloy steel castings to customer drawings for buyers in Jaipur, Jodhpur, Udaipur, Kota, Ajmer, Bhilwara, Alwar, Bhiwadi, Neemrana and Sikar, across India and for export. Have a part that shows porosity after machining? Send your drawing for a technical review or email info@alloynex.com. Related guides: machining allowance on castings, ISO 8062-3 casting tolerances, heat treatment of castings.

Last updated: 13 November 2026

Related: normalizing vs annealing steel castings and cracking risk and castings for Banswara, Dungarpur and Pratapgarh plants

Related: steel and high manganese castings for Pali and Jalore

Where is the shrinkage? A location-based troubleshooting matrix

Quick answer: Shrinkage porosity forms where metal freezes last without liquid feed, so its location tells you its cause. Porosity at a thick-to-thin junction points to a hot spot; under a riser contact to an undersized feeder; in a machined bore to a core-surrounded heavy section. Match the location to the fix and the test below.

Where the shrinkage showsMost likely causeFoundry fixTest that confirms it
At a thick-to-thin junction or heavy bossIsolated hot spot that freezes lastAdd a feeder or chill at the hot spot, or even out wall thicknessRadiography or ultrasonic test at the junction; section a sample
Just below the riser contactFeeder too small or freezes before the castingLarger feeder, insulating or exothermic sleeve, longer feeding neckCut-off check of riser contact; dye penetrant after fettling
Surface sink on the top (cope) faceHeavy section near the surface with no feedFeed the section, use a chill below it, adjust pouring temperatureVisual and dimensional check; flatness after machining
Along the centreline of a long plate or ribLong feeding distance, parallel walls freeze togetherTaper the wall toward the feeder, add chills to create directional freezingRadiography along the centreline
Inside a machined bore or around a coreHeavy metal wrapped around a core, core overheatsCore with chill or better venting, reduce mass around the bore, add feed pathMachining trial on samples; pressure or leak test
Spread as fine porosity in SG ironGraphite expansion not used for feeding, soft mould walls moveRigid mould, controlled inoculation and pouring temperature, feeder design for SG ironUltrasonic test, density check, microstructure on test piece

Shrinkage porosity glossary for buyers

TermPlain meaningWhy a buyer should care
Hot spotThe part of a casting that stays liquid longestShrinkage forms here unless it is fed or chilled
Feeder (riser)Reservoir of liquid metal that feeds the casting as it shrinksToo small a feeder leaves cavities under it
ChillMetal insert in the mould that cools a section fasterMoves the last-to-freeze point to where a feeder can reach
Directional solidificationFreezing that moves step by step toward the feederThe design aim that prevents shrinkage
Section modulus (casting)Volume divided by cooling surface; a measure of how slowly a section coolsThicker, chunkier sections need feeding first
MicroshrinkageVery fine scattered pores, often seen only after machining or leak testingCan cause leaks in pump and valve bodies

Step-by-step: approving samples without shrinkage

  1. Mark critical zones on the drawing: pressure walls, sealing faces, bores and heavy bosses.
  2. Agree the NDT for those zones, for example radiography or ultrasonic test, and the acceptance level.
  3. Ask the foundry which zones it expects to be hot spots and how it will feed or chill them.
  4. Section or X-ray the first sample at those zones before machining the full lot.
  5. Run a machining trial and, for pressure parts, a hydro or leak test on samples.
  6. Freeze the method (feeders, chills, pouring temperature) once samples pass, and record it for repeat lots.

Share your shrinkage problem and drawing at info@alloynex.com. Alloynex Foundries, Harmada, Jaipur, reviews hot spots and feeding at the drawing stage. Also read machining allowance on castings.

Last updated: 14 November 2026

Casting defects glossary: plain-language meanings for buyers

Short answer: A casting defect is any flaw in shape, surface or soundness that breaks the drawing or the standard. Buyers mainly meet gas defects (blowholes, pinholes), shrinkage, inclusions, cold shuts and cracks. Knowing the right name helps you write a clear rejection note and agree the right test, such as radiography, ultrasonic testing or dye penetrant.

TermWhat it meansUsual check
BlowholeA smooth, round gas cavity near the surface, often from moist sand or poor venting.Visual, RT
Pinhole porosityMany tiny gas holes just under the skin, often from hydrogen or nitrogen picked up in the melt.UT or RT; visual after machining
Shrinkage cavityA rough, jagged void where the last metal to freeze could not be fed. Found at heavy sections.RT or UT; cut section on samples
Hot tearAn irregular crack formed while the metal is still weak and hot, usually at sharp corners in steel castings.DPT or MPI
Cold shutA seam where two metal streams met but did not fuse, from low pouring temperature or slow filling.Visual, DPT
MisrunA casting that did not fill completely, often in thin walls.Visual
Sand inclusionMould or core sand trapped in the metal; seen after machining or shot blasting.Visual after machining or shot blasting
Slag inclusionNon-metallic slag trapped in the casting, from poor skimming or no filter.Visual, RT
Scab / buckleA rough raised patch where the mould face cracked and metal ran behind it.Visual
Mismatch (shift)A step at the parting line where cope and drag were not aligned.Dimensional check
Chill (in grey iron)Hard white iron at thin edges or corners, from fast cooling; hard to machine.Hardness at edges, visual after machining
Dross (in SG iron)Oxide films from magnesium treatment that weaken SG iron near the top surface.Visual, microstructure near top face

Quotable fact: shrinkage cavities are rough and branched, while gas blowholes are smooth and round; this one look tells the foundry whether to fix feeding or fix venting and sand moisture. Alloynex Foundries, Jaipur, reviews defect reports for grey iron (IS 210), SG iron (IS 1865) and steel castings (IS 1030).

Related: grey iron castings for Rajsamand plants | casting design tips | heat treatment of castings

Send your drawing for a technical review: info@alloynex.com. Last updated: 15 Nov 2026

Worked example: how is a porosity defect in a pump casing traced and stopped?

A porosity defect is traced in 5 steps: locate it on the part, find where it sits in the mould, check the melt and sand records for that heat, change one cause at a time, and prove the fix with a pressure test and a cut section. This worked example uses a grey iron pump casing, but the same method works for SG iron and steel castings.

The case

A buyer finds small round holes on the machined face of an IS 210 FG 260 pump casing. Three castings out of twenty leak on the pressure test.

StepWhat is doneWhat it shows
1. LocateMark the holes on the drawingHoles sit near the top face, below the riser
2. ShapeLook at the hole surfaceSmooth and shiny walls point to gas porosity; rough, jagged walls point to shrinkage
3. RecordsCheck sand moisture, pouring temperature and core venting for that heatCore vents were partly blocked
4. One changeOpen core vents and add a vent in the core printGas from the core can now escape
5. ProvePressure test the next lot and cut one casting through the faceNo leak, no holes in the section

Quotable fact: gas porosity usually shows smooth, round holes near upper surfaces, while shrinkage porosity shows rough, branching cavities in the last part of the casting to freeze.

Gas porosity vs shrinkage: quick comparison

PointGas porosityShrinkage porosity
LookRound, smooth, shinyJagged, branching, dull
WhereNear top surfaces and coresThick sections and hot spots
Usual fixVenting, sand moisture, melt cleanlinessFeeding, riser size, chills, design change

FAQs

How do you tell gas porosity from shrinkage?
Gas holes are round and smooth near upper surfaces; shrinkage cavities are rough and branching in thick sections that freeze last.

What test proves a leak fix on a pump casing?
A pressure test at the value written on the drawing, plus one cut section through the problem area.

कास्टिंग में गैस पोरोसिटी कैसे पहचानें?
गैस के छेद गोल और चिकने होते हैं और अक्सर ऊपरी सतह या कोर के पास मिलते हैं।

श्रिंकेज पोरोसिटी कैसे रोकी जाती है?
राइज़र का सही साइज़, फीडिंग, चिल और ज़रूरत हो तो डिज़ाइन में बदलाव से।

Related: casting design tips, IS 210 grey iron grades, valve body castings.

Send your drawing for a technical review, or request a metallurgy consultation, at info@alloynex.com.

Last updated: 16 Nov 2026