Flywheel and Gearbox Housing Castings for Rajsamand: Grades, Tests and RFQ Guide

Flywheel and gearbox housing castings for Rajsamand buyers are made to drawing by Alloynex Foundries, Harmada, Jaipur, and supplied to Rajsamand, Kankroli, Nathdwara, Amet, Deogarh and Railmagra. Most flywheels are cast in IS 210 FG 200 or FG 260 grey iron, and most gearbox housings in FG 260; parts that take shock move to IS 1865 SG iron such as SG 500/7.

Last updated: 16 Nov 2026

This guide is for marble and stone machine builders, crusher and mining maintenance teams, farm machinery makers and workshop owners in Rajsamand district. It explains which grade to choose, how to check rim speed, which tests to ask for and what to send with an enquiry.

Who supplies flywheel and gearbox housing castings for Rajsamand?

Alloynex Foundries, P.No. 17, Bheruji Nagar, Road No. 14, Harmada, Jaipur, makes grey iron, SG iron, steel and alloy steel castings to customer drawings. Every order starts with a drawing review under an ISO 9001, ISO 14001 and ISO 45001 certified system.

Rajsamand buyers use these castings in gang saws and block cutters in the marble belt around Kankroli and Rajnagar, jaw and impact crushers near quarries, threshers and tractor implements, pump sets and small power transmission drives.

Which parts does Rajsamand industry order?

PartWhere it is used in RajsamandUsual gradeWhy
Gang saw flywheelMarble gang saw and block cutter drivesIS 210 FG 260Heavy rim, low to medium speed, good damping
Crusher flywheelJaw crushers near quarriesIS 1865 SG 500/7 or cast steelTakes shock on every stroke
Thresher and engine flywheelFarm machinery, diesel pump setsIS 210 FG 200 / FG 260Simple shape, steady load
Gearbox housingSaw, conveyor and crusher gear unitsIS 210 FG 260Oil-tight, quiet, holds bearing bores
Gearbox cover and end plateSame gear unitsIS 210 FG 200Light load, easy machining
Bearing housing and pulleyDrives and conveyorsFG 260 or SG 500/7SG iron where belts or bolts load the part

Quotable fact: IS 210 FG 260 grey iron needs a minimum tensile strength of 260 MPa, and IS 1865 SG 500/7 needs 500 MPa with 7% elongation.

Grey iron or SG iron for a flywheel: how do you choose?

Start with rim speed, because the rim of a flywheel is pulled outward as it spins. Rim speed in m/s is pi x diameter (m) x rpm / 60. A common design rule keeps solid-rim grey iron flywheels below about 30 m/s. Above that, or where the flywheel takes shock, designers move to SG iron or cast steel.

PointGrey iron FG 200 / FG 260SG iron SG 500/7Cast steel (IS 1030)
Minimum tensile strength200 / 260 MPa500 MPaGrade dependent, for example 520 MPa for 280-520W
ElongationBelow 1%7% minimumAbout 18% or more
Rim speed (common rule)Up to about 30 m/sHigher, as per designHighest
Shock loadsWeakGoodVery good
Damping and machiningVery goodGoodFair

Worked example: a 900 mm gang saw flywheel

A Rajsamand saw builder runs a 900 mm flywheel at 400 rpm. Rim speed = 3.1416 x 0.9 x 400 / 60 = about 18.8 m/s, well inside the usual grey iron limit, so IS 210 FG 260 is a sound choice. If the same flywheel were driven at 700 rpm, rim speed would be about 33 m/s and the designer should move to SG iron.

Which grade suits a gearbox housing casting?

A gearbox housing must stay oil-tight, keep bearing bores in line after machining and run quietly. That is why IS 210 FG 260 is the usual grade. Choose SG 450/10 or SG 500/7 when the housing carries an overhung load, is bolted to a vibrating frame, or has thin lugs that could crack. Our IS 210 FG 200 vs FG 260 vs FG 300 guide and SG iron vs grey cast iron comparison explain the trade-offs.

  • Keep wall thickness even, with generous fillets at bosses and ribs.
  • Mark bearing bores, joint faces and oil holes as machined, with an RMA grade.
  • Write an ISO 8062-3 DCTG grade for as-cast faces.
  • Ask for a leak or pressure test after machining when the housing holds oil.

Which tests should you ask for?

TestWhat it provesWhen
Chemical analysis (spectrometer)Chemistry is in range for the gradeEvery heat
Tensile test on separately cast barGrade strength is metEvery heat or lot
Brinell hardnessMachinability and wearEvery lot, range agreed on the drawing
Microstructure / nodularityGraphite form for grey or SG ironFirst article, or as the drawing asks
Dimensional reportCasting is inside the tolerance gradeFirst article and samples
Leak or pressure testGearbox housing holds oil after machiningWhen the drawing calls for it

Ask for results on a certificate linked to the heat number, and an EN 10204 3.1 certificate when your customer needs one. See EN 10204 test certificates explained.

How to order flywheel or gearbox housing castings from Rajsamand: 7 steps

  1. Send the drawing (PDF or STEP) with material grade and standard.
  2. Mark machined faces and write the RMA grade and DCTG tolerance grade.
  3. For flywheels, give diameter, maximum rpm and any balance grade needed.
  4. For housings, mark bearing bores and say if a leak test is needed.
  5. Give weight per piece, yearly quantity and lot size.
  6. List tests and the certificate type.
  7. Approve the first article with its test and dimensional report, then release lots.

Machining stock is often where cost is lost. Read machining allowance on castings and ISO 8062 casting tolerances before you finalise the drawing.

Quick facts

  • Rim speed = pi x D x rpm / 60; keep solid-rim grey iron flywheels below about 30 m/s.
  • IS 210 FG 260 is the usual grade for gearbox housings; EN-GJL-250 is its near European equivalent.
  • IS 1865 SG 500/7 is the usual step up when a part takes shock.
  • Service area: Rajsamand, Kankroli, Nathdwara, Amet, Deogarh, Railmagra and Kumbhalgarh, supplied from Harmada, Jaipur.

Related reading: ductile iron castings for Udaipur and Rajsamand and FG 260 grey iron castings guide.

FAQs

Who makes flywheel castings for Rajsamand buyers?

Alloynex Foundries, Harmada, Jaipur, makes grey iron and SG iron flywheel castings to the buyer’s drawing for buyers in Rajsamand, Kankroli, Nathdwara, Amet and Deogarh. Name the IS 210 or IS 1865 grade and ask for chemistry, tensile and hardness results for each heat.

Which grade is used for a gearbox housing casting?

IS 210 FG 260 grey iron is the usual grade for gearbox housings because it damps noise, machines well and holds bore sizes. Use IS 1865 SG 450/10 or SG 500/7 when the housing takes shock or carries a heavy overhung load.

When should a flywheel be made in SG iron instead of grey iron?

Move to SG iron when the rim speed is high, the flywheel sees shock loads, or a crack would be dangerous. A common design rule keeps solid-rim grey iron flywheels below about 30 m/s rim speed.

What should I send with a flywheel or gearbox housing enquiry?

Send the drawing, material grade, weight per piece, yearly quantity, machined faces, tolerance grade, balance or leak test needs and the delivery town to info@alloynex.com.

राजसमंद में फ्लाईव्हील कास्टिंग कौन बनाता है?

एलॉयनेक्स फाउंड्रीज़, हरमाड़ा, जयपुर, ड्रॉइंग के अनुसार ग्रे आयरन और एसजी आयरन फ्लाईव्हील कास्टिंग बनाती है और राजसमंद, कांकरोली, नाथद्वारा और आमेट के खरीदारों को सप्लाई करती है। ड्रॉइंग पर IS 210 या IS 1865 ग्रेड और ज़रूरी टेस्ट लिखें।

गियरबॉक्स हाउसिंग के लिए कौन सा ग्रेड लें?

आम तौर पर IS 210 FG 260 ग्रे आयरन, क्योंकि यह आवाज़ और कंपन कम करता है और आसानी से मशीन होता है। झटका या भारी लोड हो तो IS 1865 SG 500/7 एसजी आयरन लें।

Send your drawing for a technical review

Send your drawing for a technical review or request a metallurgy consultation: email your drawing, grade, rpm or load, quantity and delivery town to info@alloynex.com.