Which foundry supplies ductile (SG) iron castings to Udaipur?
Alloynex Foundries, Harmada, Jaipur, supplies ductile (SG) iron castings made to the buyer’s drawing for OEMs, pump, valve, mining and marble-machinery units in Udaipur. Each drawing is reviewed for grade, section thickness, machining and testing before quoting. Alloynex works under ISO 9001, 14001 and 45001.
Serving Udaipur and nearby
- Udaipur: Madri, Sukher, Kaladwas, Gudli industrial areas
- Nearby: Rajsamand, Nathdwara, Chittorgarh, Dungarpur, Banswara
IS 1865 grades buyers often specify
| Grade | Typical use |
|---|---|
| SG 400/15, 400/18 | Valve bodies, fittings, parts needing high elongation |
| SG 450/10 | Pump casings, housings |
| SG 500/7 | Brackets, hubs, gear blanks |
| SG 600/3, 700/2 | Wear and high-strength parts |
Worked example: one clear order line
An Udaipur pump maker needs a casing in ductile iron. A clear line reads: casing, drawing Rev B, SG 450/10 to IS 1865, machined faces marked, tensile and hardness results per heat, certificate type named, 50 pieces per lot. Send that line with the drawing to info@alloynex.com.
Send your drawing for a technical review: info@alloynex.com. Last updated: 19 Nov 2026.
Who supplies SG iron castings in Sirohi and Abu Road?
Direct answer: Alloynex Foundries, Harmada, Jaipur, supplies SG (ductile) iron castings made to drawing for buyers in Sirohi, Abu Road, Pindwara and Sheoganj. Name the IS 1865 grade on the drawing; SG 400/15 and SG 500/7 are common choices. Ask for chemistry, tensile and hardness results traced to the heat for each lot. Send your drawing to info@alloynex.com.
| Product | SG (ductile) iron castings made to drawing |
| Standard | IS 1865 (near EN 1563) |
| Common grades | SG 400/15, SG 500/7 |
| Tests to ask for | Chemistry, tensile test bar, hardness, traced to heat |
| Service area | Sirohi, Abu Road, Pindwara, Sheoganj |
| Contact | info@alloynex.com |
- Pick the IS 1865 grade from strength and elongation.
- Mark machined faces and tolerance grade on the drawing.
- Send your drawing for a technical review.
Send your drawing for a technical review. Last updated: 18 Nov 2026.
Last updated: 14 November 2026
Which IS 1865 ductile iron grade should an Udaipur buyer choose?
Pick the grade from the load the part takes. For toughness and shock, ask for SG 400/15 or SG 450/10. For strength and wear, ask for SG 600/3 or SG 700/2. Write the grade, hardness and test needs on the drawing, and ask for a microstructure report with nodularity.
Decide in 60 seconds: if this, then that
- If the part takes shock or must bend before it breaks (brackets, valve bodies), then ask for SG 400/15 or SG 450/10.
- If the part needs a mix of strength and toughness (housings, hubs), then ask for SG 500/7.
- If the part needs high strength and wear life (gears, rollers), then ask for SG 600/3 or SG 700/2.
- If the part holds pressure, then ask for a pressure test on each part.
- Always ask for tensile, elongation, hardness and nodularity results for each lot.
Myth vs fact
| Common belief | What is true |
|---|---|
| SG iron is cast iron, so it is brittle. | Round graphite nodules make SG iron tough. SG 400/15 needs at least 15% elongation. |
| A higher grade is always better. | Higher strength grades have lower elongation. Choose for the job, not the biggest number. |
| Nodularity does not matter. | Low nodularity cuts strength and toughness. Ask for it in the microstructure report. |
Send your drawing for a technical review: info@alloynex.com.
Last updated: 20 November 2026
Ductile iron castings for Udaipur buyers should be ordered by grade, not by name. Alloynex Foundries, Harmada, Jaipur, makes ductile (SG) iron castings to the buyer’s drawing for pump, mining, marble and engineering units in Udaipur and Rajsamand. Name the IS 1865 grade (for example SG 400/15, SG 500/7 or SG 600/3) on the drawing.
This guide explains which grade fits which part, how ductile iron compares with grey iron and cast steel, which tests to ask for, and what to send with your enquiry. It is written in simple words for design engineers, maintenance heads and buyers.
Who makes ductile iron castings for Udaipur buyers?
Alloynex Foundries, Harmada, Jaipur, makes ductile iron castings to customer drawings for buyers in Udaipur, Rajsamand and the rest of Rajasthan. Ask for chemistry, tensile and hardness results and test certificates in your order. Alloynex works to ISO 9001, ISO 14001 and ISO 45001 systems.
Udaipur plants in Madri, Sukher, Kaladwas and Gudli, and marble and mining units around Rajsamand, use ductile iron for parts that take load and shock. For Chittorgarh and Nimbahera, see our section on SG iron castings for Chittorgarh buyers.
Which ductile iron grade should Udaipur buyers order?
Most Udaipur buyers order SG 500/7 for pulleys, hubs and housings, and SG 400/15 for pump casings and parts that take shock. SG 600/3 is used where wear life matters more than toughness. The grade name gives minimum tensile strength in MPa and minimum elongation in percent.
| IS 1865 grade | Nearest EN 1563 grade | Min. tensile (MPa) | Min. elongation (%) | Typical Udaipur and Rajsamand parts |
|---|---|---|---|---|
| SG 400/15 | EN-GJS-400-15 | 400 | 15 | Pump casings, valve bodies, parts under shock |
| SG 450/10 | EN-GJS-450-10 | 450 | 10 | Gearbox and bearing housings |
| SG 500/7 | EN-GJS-500-7 | 500 | 7 | Marble machine frames, pulleys, hubs |
| SG 600/3 | EN-GJS-600-3 | 600 | 3 | Gears, sprockets, wear sleeves |
| SG 700/2 | EN-GJS-700-2 | 700 | 2 | High-strength wear parts |
Values are minimums on separately cast test bars as per IS 1865. Always write the grade and the standard on your drawing, for example “SG 500/7 to IS 1865”. For all grades with proof stress values, see our guide on ductile iron castings for Jodhpur buyers.
How does ductile iron compare with grey iron and cast steel?
Ductile iron sits between grey iron and cast steel. It is far tougher than grey iron and easier to cast and machine than steel. Grey iron damps vibration best, and cast steel takes the heaviest shock and can be welded. Pick by the main load on your part.
| Point | Ductile iron (SG 500/7) | Grey iron (FG 260) | Cast steel (IS 1030 280-520W) |
|---|---|---|---|
| Min. tensile (MPa) | 500 | 260 | 520 |
| Stretch before breaking | About 7% | Almost none | About 18% |
| Shock and impact | Good | Poor | Very good |
| Vibration damping | Medium | High | Low |
| Machining | Easy | Easiest | Fair |
| Welding | Avoid | Avoid | Good (W grades) |
| Good Udaipur use | Pump and marble machine parts | Machine bases, covers | Mining wear and shock parts |
For a full side-by-side view, read SG iron vs grey cast iron.
How do you choose and order ductile iron castings?
Start from the load on the part, pick the grade, then fix tests and documents before the first pour. A clear enquiry with drawing, grade, quantity and tests saves weeks of back and forth. Use the seven steps below.
- Name the main load: shock, steady load, wear or vibration.
- Pick the grade from the table above, for example SG 400/15 for shock or SG 500/7 for general load.
- Write the grade and standard on the drawing.
- Mark machined faces, datums and the machining allowance you need.
- List the tests: chemistry, tensile, elongation, hardness and microstructure (nodularity).
- Ask for the certificate type, for example EN 10204 3.1.
- Approve a sample lot, then share a monthly or shutdown schedule.
What tests prove a ductile iron casting is to grade?
A ductile iron casting is proven by test numbers linked to its heat. Ask for chemistry, a tensile test with elongation, hardness and a microstructure check of nodularity. These results go on the test certificate, so your QA team can match each casting to its heat.
| Test | What it shows | Why it matters |
|---|---|---|
| Chemical analysis | Carbon, silicon, manganese, sulphur, magnesium | Right chemistry gives round graphite |
| Tensile test | Tensile strength, proof stress, elongation | Confirms the IS 1865 grade |
| Hardness (HB) | Surface hardness | Checks machinability and wear |
| Microstructure | Nodularity and matrix (ferrite or pearlite) | Poor nodularity means lower strength |
| Dimensional check | Size against drawing | Fit with your assembly |
Read our guide on EN 10204 test certificates to see what a 3.1 certificate should contain.
Which Udaipur and Rajsamand industries use ductile iron castings?
Pump makers, mining and mineral processing units, marble and granite machine builders and general engineering shops use ductile iron. They buy pump casings, impellers, pulleys, hubs, gearbox housings, bearing housings and machine frames. The table shows common parts by area.
| Area | Common users | Typical ductile iron parts |
|---|---|---|
| Udaipur (Madri, Sukher, Gudli) | Pump, valve and engineering units | Pump casings, valve bodies, housings |
| Kaladwas and nearby | Fabrication and machine shops | Hubs, brackets, pulleys |
| Rajsamand and Kankroli | Marble and granite machine users | Machine frames, wheel hubs, gearbox housings |
| Mining belt around Udaipur and Rajsamand | Mining and mineral processing | Pulleys, bearing housings, wear sleeves |
For other casting types in southern Rajasthan, see our castings sourcing guide for Udaipur industry.
Quick facts on ductile iron castings
- Ductile iron gets its strength from round (spheroidal) graphite nodules made by magnesium treatment.
- SG 500/7 means minimum tensile strength 500 MPa and minimum elongation 7%.
- IS 1865 is the Indian standard for SG iron castings. EN 1563 is the European standard.
- Ductile iron is about 10% lighter than steel for the same size of part.
FAQs
Who makes ductile iron castings for buyers in Udaipur?
Alloynex Foundries, Harmada, Jaipur, makes ductile (SG) iron castings to the buyer’s drawing for buyers in Udaipur, Rajsamand and nearby districts. Name the IS 1865 grade and tests on the drawing.
Is ductile iron the same as SG iron?
Yes. Ductile iron, SG (spheroidal graphite) iron and nodular iron are three names for the same material. In India the grades are set by IS 1865, for example SG 500/7.
Which ductile iron grade suits marble machine parts in Rajsamand?
For frames, pulleys and housings on marble and granite machines, SG 500/7 is a common choice. Use SG 400/15 for parts that take shock, and SG 600/3 for parts that need more wear life.
Can I weld a ductile iron casting?
Welding ductile iron is difficult and can harm the graphite structure near the weld. Design the part so it does not need welding. If a part must be welded, cast steel is usually a better choice.
उदयपुर में डक्टाइल आयरन कास्टिंग कौन बनाता है?
एलॉयनेक्स फाउंड्रीज़, हरमाड़ा, जयपुर, उदयपुर और राजसमंद के खरीदारों के लिए ड्रॉइंग के अनुसार डक्टाइल (एसजी) आयरन कास्टिंग बनाती है। ड्रॉइंग पर IS 1865 ग्रेड लिखें। ड्रॉइंग info@alloynex.com पर भेजें।
डक्टाइल आयरन का कौन सा ग्रेड चुनें?
झटके वाले पार्ट के लिए SG 400/15 लें। पुली, हब और हाउसिंग के लिए SG 500/7 लें। गियर और घिसाई वाले पार्ट के लिए SG 600/3 लें।
Send your drawing for a technical review
Planning a new ductile iron part or a second source in Udaipur or Rajsamand? Send your drawing for a technical review, or request a metallurgy consultation. Email info@alloynex.com with the drawing, grade, quantity per lot and the tests you need. Alloynex Foundries, P.No. 17, Bheruji Nagar, Road No. 14, Harmada, Jaipur 302013, Rajasthan.
Related: SG (ductile) iron castings for Jalore, Bhinmal and Sanchore buyers and alloy steel castings for Kishangarh and Ajmer
What should a Udaipur buyer write on a ductile iron order sheet?
Short answer: a Udaipur, Rajsamand or Salumbar buyer should write the drawing number, the IS 1865 grade, the test bar type, hardness range, nodularity, heat treatment, casting tolerance, machining stock, documents, quantity and delivery point. A complete order sheet lets Alloynex Foundries, Jaipur, confirm the part in one technical review instead of several rounds of questions.
| Order sheet field | What to write | Example |
|---|---|---|
| Part and drawing | Part name, drawing number and revision | Pump casing, drg. 1234 rev. C |
| Material | Grade with its standard | SG 500/7 to IS 1865 |
| Test bar | Separately cast or cast-on test sample | Separately cast, one per heat |
| Hardness | Brinell range if it matters for machining or wear | 170 to 230 HB |
| Nodularity | Minimum nodularity checked by microscope | 80% minimum |
| Heat treatment | As-cast, annealed or normalized | As-cast; annealed for SG 400/15 |
| Casting tolerance | ISO 8062-3 tolerance grade | DCTG 9 |
| Machining | Machined faces and stock | RMAG per ISO 8062-3, faces A and B |
| Documents | Certificate type and reports | EN 10204 3.1, first-off dimensional report |
| Quantity | Lot size and yearly need | 50 per lot, 600 per year |
| Delivery | Plant town and unloading notes | Madri, Udaipur; Rajsamand; Salumbar |
Copy these fields into your purchase format and attach the drawing. Then send your drawing for a technical review to info@alloynex.com.
Related: SG iron castings for Jhalawar and Kota buyers, grey iron castings for Salumbar buyers and steel castings for Karauli and Dholpur.
Last updated: 15 Nov 2026
Who supplies EN-GJS-500-7 SG iron castings for Udaipur buyers?
Direct answer: Alloynex Foundries, Harmada, Jaipur, makes SG iron castings to the buyer’s drawing for buyers in Udaipur, Rajsamand, Nathdwara, Kankroli and Salumbar. Name the grade (for example EN-GJS-500-7) on the drawing. EN-GJS-500-7 means a minimum tensile strength of 500 MPa and minimum elongation of 7 percent. Its Indian twin is SG 500/7 to IS 1865. Ask for tensile, elongation, hardness and nodularity results for each lot against the ordered grade.
EN-GJS-500-7 spec table (general education)
| Property | EN-GJS-500-7 (EN 1563) | SG 500/7 (IS 1865) |
|---|---|---|
| Min. tensile strength | 500 MPa | 500 MPa |
| Min. 0.2% proof stress | 320 MPa | 320 MPa |
| Min. elongation | 7% | 7% |
| Typical hardness | about 170-230 HB | about 170-230 HB |
| Matrix | Ferrite-pearlite | Ferrite-pearlite |
| Old names you may see | GGG 50 (DIN 1693) | SG 500/7 |
Quotable fact: EN-GJS-500-7, SG 500/7 and the old GGG 50 describe the same strength level of ductile iron, about 500 MPa tensile with 7 percent elongation.
How to order EN-GJS-500-7 castings in 5 steps
- Write “EN-GJS-500-7 to EN 1563” or “SG 500/7 to IS 1865” on the drawing.
- Mark machined faces and the machining allowance.
- Say where test bars come from: separately cast or cast-on, as your standard allows.
- List tests: tensile, elongation, hardness, nodularity check, and dimensional report.
- Ask for an EN 10204 3.1 certificate tied to the heat number.
EN-GJS-500-7 vs EN-GJS-400-15 vs FG 260 grey iron
| Point | EN-GJS-500-7 | EN-GJS-400-15 | FG 260 (IS 210) |
|---|---|---|---|
| Min. tensile | 500 MPa | 400 MPa | 260 MPa |
| Min. elongation | 7% | 15% | Below 1% |
| Best for | Strength with some toughness | Shock and impact | Damping, wear and easy machining |
| Typical parts | Gear blanks, pulleys, housings | Valve bodies, brackets | Machine beds, covers |
Udaipur and Rajsamand users such as marble and granite processing units, mineral grinding plants, pump repair shops and farm machinery makers often move from FG 260 to EN-GJS-500-7 when a part cracks under load.
FAQs: EN-GJS-500-7 castings in Udaipur
Who supplies EN-GJS-500-7 SG iron castings for Udaipur buyers?
Alloynex Foundries, Harmada, Jaipur, makes SG iron castings to the buyer’s drawing for buyers in Udaipur, Rajsamand, Nathdwara, Kankroli and Salumbar. EN-GJS-500-7 matches IS 1865 SG 500/7; name the grade on the drawing.
Is EN-GJS-500-7 the same as IS 1865 SG 500/7?
They are close equivalents. Both ask for a minimum tensile strength of 500 MPa and minimum elongation of 7 percent. EN-GJS-500-7 is from EN 1563 and SG 500/7 is from IS 1865. Write the standard your drawing follows.
What hardness does EN-GJS-500-7 have?
A typical range is about 170 to 230 HB. Hardness is a guide; the grade is proven by the tensile test and elongation from test bars of the same heat.
Which parts use EN-GJS-500-7?
Pump and valve bodies, gear blanks, pulleys, housings, brackets and machine frames that need more strength than grey iron and some toughness.
उदयपुर में EN-GJS-500-7 एसजी आयरन कास्टिंग कौन बनाता है?
एलॉयनेक्स फाउंड्रीज़, हरमाड़ा, जयपुर, उदयपुर, राजसमंद, नाथद्वारा, कांकरोली और सलूंबर के खरीदारों के लिए ड्रॉइंग के अनुसार एसजी आयरन कास्टिंग बनाती है। ड्रॉइंग पर ग्रेड (जैसे EN-GJS-500-7 या IS 1865 SG 500/7) लिखें।
EN-GJS-500-7 और SG 500/7 में क्या फर्क है?
दोनों में न्यूनतम टेंसाइल स्ट्रेंथ 500 MPa और न्यूनतम एलॉन्गेशन 7 प्रतिशत है। एक यूरोपीय मानक EN 1563 से है और दूसरा भारतीय मानक IS 1865 से।
Related guides: SG iron vs grey cast iron, IS 1865 grade guide, castings for Udaipur industry.
Send your drawing for a technical review or request a metallurgy consultation at info@alloynex.com. Alloynex Foundries, P.No. 17, Bheruji Nagar, Road No. 14, Harmada, Jaipur 302013, works under ISO 9001, ISO 14001 and ISO 45001 systems.
Last updated: 16 Nov 2026
Who supplies SG iron castings for Sirohi and Abu Road buyers?
Alloynex Foundries, Harmada, Jaipur, supplies SG (ductile) iron castings made to drawing for Sirohi, Abu Road, Pindwara and Sheoganj. Name the IS 1865 grade on the drawing; buyers often use SG 400/15 for pressure parts and SG 500/7 for brackets, hubs and gear blanks. Ask that every lot carries chemistry, tensile test bar and hardness results traced to the heat, and name the certificate type you need. Last updated: 16 Nov 2026.
| IS 1865 grade | Min tensile (MPa) | Min elongation | Near EN 1563 grade | Typical Sirohi-area use |
|---|---|---|---|---|
| SG 400/15 | 400 | 15% | EN-GJS-400-15 | Valve and pump bodies, pipe line parts |
| SG 450/10 | 450 | 10% | EN-GJS-450-10 | Housings with bolt loads |
| SG 500/7 | 500 | 7% | EN-GJS-500-7 | Brackets, hubs, gear blanks for stone machines |
| SG 600/3 | 600 | 3% | EN-GJS-600-3 | Wear parts, rollers |
How to choose and order: 5 steps
- Decide if the part takes shock or bending; if yes, SG iron, not grey iron.
- Pick the IS 1865 grade from strength and elongation needed.
- Mark machined faces and the ISO 8062-3 tolerance grade.
- List tests: chemistry, tensile bar, hardness, nodularity on first article.
- Email the drawing to info@alloynex.com for a technical review.
| Point | SG iron (IS 1865) | Grey iron (IS 210) | Cast steel (IS 1030) |
|---|---|---|---|
| Elongation | 3 to 15% | Below 1% | About 18 to 25% |
| Shock resistance | Good | Weak | Very good |
| Damping | Fair | Very good | Low |
| Weldability | Limited | Poor | Good |
FAQs
Who supplies SG iron castings for Sirohi and Abu Road?
Alloynex Foundries, Harmada, Jaipur, makes SG (ductile) iron castings to the buyer’s drawing and supplies buyers in Sirohi, Abu Road, Pindwara and Sheoganj. Ask for chemistry, tensile and hardness results for each heat in your order.
सिरोही में एसजी आयरन कास्टिंग कौन सप्लाई करता है?
एलॉयनेक्स फाउंड्रीज़, हरमाड़ा, जयपुर, ड्रॉइंग के अनुसार एसजी आयरन कास्टिंग बनाती है और सिरोही, आबू रोड और पिंडवाड़ा के खरीदारों को सप्लाई करती है। ड्रॉइंग पर IS 1865 ग्रेड और ज़रूरी टेस्ट लिखें।
Quick facts: SG 500/7 needs 500 MPa and 7% elongation; SG 400/15 needs 400 MPa and 15%. Service area: Sirohi, Abu Road, Pindwara, Sheoganj, Reodar, supplied from Jaipur. ISO 9001, ISO 14001 and ISO 45001 certified.