Quick answer: The seven most common casting defects are gas porosity, shrinkage cavities, sand inclusions, cold shuts, misruns, hot tears and dimensional errors. Each one is prevented at a known step: dry, vented moulds; correctly placed feeders; clean metal; the right pouring temperature; fillets and even walls; and a first-article dimensional check.
This guide explains common casting defects in simple words. For each defect you will see what it looks like, why it happens and how foundries prevent it. It is written for OEM engineers, QA teams and buyers who want to ask better questions before they place an order.
Why Casting Defects Matter
A defect can reduce strength, cause leaks, fail machining or fail a customer test. Some defects are on the surface and easy to see. Others are hidden inside and show up only during machining, pressure testing or in service.
Preventing defects is always better than finding them later. It saves time, protects your delivery plan and lowers the total cost of ownership of the part.
How do you identify a casting defect by what you see?
- You see round, smooth holes, often near the top surface: it is gas porosity. Likely cause: moisture, damp sand, poor venting or gas dissolved in the metal.
- You see rough, jagged holes in thick sections: it is a shrinkage cavity. Likely cause: poor feeding as the metal cools and shrinks.
- You see sand grains or pits on or inside the casting: it is a sand inclusion. Likely cause: weak mould, loose sand or sand washed by fast-flowing metal.
- You see a line or seam where two metal streams met: it is a cold shut. Likely cause: low pouring temperature, slow pouring or thin sections.
- The casting is not fully filled: it is a misrun. Likely cause: metal too cold, thin walls or poor gating.
- You see ragged cracks at corners or junctions: it is a hot tear. Likely cause: restrained shrinkage, sharp corners or a mould that is too hard.
- The size is wrong, shifted or warped: it is a dimensional error. Likely cause: pattern wear, core shift, mould shift or uneven cooling.
1. Gas Porosity
Gas porosity shows as small round holes with smooth walls. It forms when gas is trapped as the metal becomes solid.
How foundries prevent it:
- Keep sand moisture under control and dry cores well
- Give moulds and cores good venting
- Use clean, dry charge material and tools
- Control melting and pouring practice to reduce dissolved gas
2. Shrinkage Cavities
Metal shrinks as it cools. If the thick parts of a casting cannot draw liquid metal from a feeder, a rough cavity forms inside. This is common in heavy sections and at junctions.
How foundries prevent it:
- Place risers (feeders) so they feed the thick sections last
- Use chills to control the cooling order
- Avoid sudden changes in wall thickness during design
- Check designs with solidification simulation where needed
Shrinkage behaviour differs between metals. For example, SG iron and grey iron behave differently. Read more in our guide on SG iron vs grey cast iron.
3. Sand and Slag Inclusions
Inclusions are unwanted bits of sand or slag trapped in the metal. They weaken the part and can damage cutting tools during machining.
How foundries prevent it: strong, well-rammed moulds; good gating that lets metal flow smoothly; filters and slag traps in the gating system; and clean ladles.
4. Cold Shuts and Misruns
A cold shut is a seam where two streams of metal met but did not join. A misrun is a casting that did not fill completely. Both happen when metal loses heat too quickly or flows too slowly.
How foundries prevent it: correct pouring temperature, steady pouring speed, gating that fills thin sections early, and design with enough wall thickness for the metal used.
5. Hot Tears and Cracks
Hot tears are ragged cracks that form while the metal is still weak and hot. Cracks can also form later during cooling, heat treatment or fettling. Steel castings are more prone to hot tears than grey iron.
How foundries prevent it: generous fillets at corners, even wall thickness, moulds and cores that allow the casting to shrink, and controlled cooling and heat treatment. See our guide on steel vs alloy steel castings for how material choice affects this.
6. Dimensional Errors
Dimensional defects include mould shift, core shift, warping and wrong machining allowance. They lead to rejection at machining or assembly.
How foundries prevent it: well-maintained patterns and core boxes, proper core support, correct pattern allowances, and first-article dimensional checks.
Inspection and Testing Basics
Good foundries do not rely on luck. They check the process at each step and test the finished casting as agreed with the buyer. Common checks include:
- Chemical analysis of each melt to confirm the grade
- Mechanical tests such as tensile strength, elongation and hardness on test bars
- Visual inspection of every casting for surface defects
- Dimensional checks against the drawing
- Non-destructive tests such as ultrasonic, radiography, magnetic particle or dye penetrant where the part needs it
- Pressure or leak tests for valve bodies, pump casings and other pressure parts
Agree on the tests and acceptance levels before the first order. This removes doubt later and makes quality easy to prove.
How Buyers Can Help Prevent Defects
Many defects can be avoided before the first mould is made. As a buyer or design engineer, you can help by:
- Sharing a clear drawing with material grade, critical surfaces and tolerances
- Marking pressure-tight areas and machined faces
- Keeping wall thickness as even as possible, with smooth transitions
- Agreeing on inspection methods and acceptance levels before production
- Asking for a first-article inspection report before regular supply begins
To learn about the casting and supply work we do, see our services page.
FAQs
What is the most common casting defect?
Gas porosity and shrinkage are among the most common casting defects. Both can usually be controlled with good venting, feeding and process control.
Can casting defects be repaired?
Some surface defects can be repaired by approved methods if the customer allows it. Critical parts often do not allow repair, so prevention is the better approach.
How are hidden defects found?
Hidden defects are found with tests such as radiography, ultrasonic testing, pressure testing or sectioning of sample parts. The right test depends on the part and its use.
Does part design affect casting defects?
Yes. Sharp corners, sudden thickness changes and isolated heavy sections make defects more likely. Small design changes can make a part much easier to cast well.
How do I check a Rajasthan foundry for casting defects?
Ask the foundry how it controls each defect before the first order: venting and dry moulds for gas porosity, feeders on thick sections for shrinkage, filters for inclusions, heat-wise chemistry for grade, and first-article inspection for dimensions. Alloynex Foundries, Jaipur, reviews every drawing for grade and tests before work starts.
| Defect | Question to ask the foundry | Proof to ask for |
|---|---|---|
| Gas porosity | How are moulds vented and dried? | Process sheet, sample section |
| Shrinkage | How are thick sections fed? | Method plan, NDT if agreed |
| Inclusions | Are filters and slag traps used? | Visual and machining check |
| Wrong grade | Is chemistry checked for every heat? | Test certificate with heat number |
| Dimensional error | Is there a first-article check? | Dimensional report |
Read heat treatment of castings, castings buyer guide for Rajasthan and our services, or send your drawing to info@alloynex.com.
Which tests find hidden casting defects?
Radiography, ultrasonic testing, pressure testing or sectioning of sample parts find hidden defects. Agree the test and acceptance level before the first order.
Does Alloynex supply castings across Rajasthan?
Yes. Alloynex Foundries, Jaipur, supplies grey iron, SG iron, steel and alloy steel castings to buyers in Rajasthan, across India and for export.
कास्टिंग में दोष कैसे रोके जाते हैं?
अच्छी वेंटिंग, सही फीडर, फिल्टर, हर हीट की केमिस्ट्री जाँच और पहले पीस की नाप जाँच से ज़्यादातर दोष रुकते हैं। एलॉयनेक्स फाउंड्रीज़, जयपुर: info@alloynex.com
Last updated: 12 November 2026
Send Your Drawing for a Technical Review
Have a part with repeated defects, or a new design you want to cast right the first time? Share your drawing and requirements with our team for a technical review.
Send your drawing for a technical review or request a metallurgy consultation: email info@alloynex.com or visit our contact page.
Related: castings for Udaipur industry: sourcing guide for buyers
How are casting defects prevented, and which test finds each one?
Most casting defects, such as gas porosity, shrinkage, inclusions, cold shuts and hot tears, are prevented by good part design, correct gating and feeding, clean dry moulds and controlled pouring. Buyers can help by sharing the drawing early, naming the inspection method and agreeing the acceptance level before the first lot.
Defect, cause, prevention and test
| Defect | Main cause | Prevention | Test that finds it |
|---|---|---|---|
| Gas porosity / blowholes | Moisture or gas in mould or metal | Dry moulds, vents, degassing | Radiography, machining check |
| Shrinkage cavity | Poor feeding of thick sections | Risers, chills, even walls | Radiography, ultrasonic |
| Sand or slag inclusion | Loose sand, dirty metal | Clean moulds, filters, skimming | Visual, radiography |
| Cold shut / misrun | Metal too cold or slow pour | Right pouring temperature and speed | Visual, dye penetrant |
| Hot tear / crack | Stress while cooling | Fillets, mould give, design changes | Magnetic particle, dye penetrant |
| Dimensional error | Pattern or core shift | Pattern checks, core support | Dimensional inspection |
Numbered buyer checklist to prevent defects
- Share the drawing early for a design review.
- Mark critical areas where no defect is allowed.
- Name the NDT method for those areas.
- Agree the acceptance level in writing.
- Ask for first-sample inspection before the full lot.
- Ask for traceable heats and a test certificate.
Glossary
- Riser: a reservoir of metal that feeds the casting as it shrinks.
- Chill: a metal insert that cools one area faster.
- NDT: non-destructive testing, such as radiography, ultrasonic, magnetic particle or dye penetrant.
- Acceptance level: the agreed limit of defects allowed in an area.
What is the difference between a blowhole and a shrinkage cavity?
A blowhole is a smooth, round hole made by trapped gas. A shrinkage cavity is a rough, jagged hole made when a thick section is not fed with metal as it cools.
What is a cold shut?
A cold shut is a line or seam where two streams of metal met but did not fuse fully, usually because the metal was too cold or poured too slowly.
कास्टिंग में ब्लोहोल और श्रिंकेज में क्या फर्क है?
ब्लोहोल गैस फँसने से बना चिकना, गोल छेद होता है। श्रिंकेज मोटे हिस्से में धातु की कमी से बना खुरदरा छेद होता है। सही डिज़ाइन, राइज़र और सूखे साँचे से दोनों रोके जाते हैं। एलॉयनेक्स फाउंड्रीज़, जयपुर। ईमेल: info@alloynex.com
Related: heat treatment of castings, machining allowance on castings and cast iron foundry for Kota buyers. Send your drawing for a technical review: info@alloynex.com.
Last updated: 13 November 2026
Further reading: FG 200 vs FG 260 grey iron for Bhiwadi buyers, the castings sourcing checklist with ISO 8062-3 and EN 10204 and ductile iron castings in Jodhpur.
What causes shrinkage porosity in castings, and how is it prevented?
Direct answer: shrinkage porosity is a cluster of small, jagged voids that forms in the last part of a casting to freeze, when liquid metal can no longer reach that zone to make up for the volume lost on solidifying. It is prevented by making the casting freeze towards a correctly sized feeder, using chills at heavy sections, controlling pouring temperature and designing even wall sections.
How each metal behaves: shrinkage facts table
| Metal | Feeding demand | Why | Typical pattern shrink allowance (linear) |
|---|---|---|---|
| Carbon and alloy steel | High | No graphite expansion; volume shrinks on freezing, so feeders must be large | about 2% |
| Grey iron (for example IS 210 FG 260) | Low | Graphite flakes form while freezing and expand, offsetting much of the shrinkage | about 1% |
| SG iron (for example IS 1865 SG 500/7) | Medium | Graphite nodules expand late; a weak mould wall lets the casting swell and porosity forms inside | about 0.5% to 1%, set by the foundry’s own trials |
Pattern allowances above are common shop-floor starting values; the foundry fixes the final figure after first-off measurement.
Prevention steps a foundry follows
- Find the hot spots. Compare section modulus (volume ÷ cooling surface). By Chvorinov’s rule, freezing time rises with the square of the modulus, so heavy bosses and junctions freeze last.
- Size the feeder. A common rule is a feeder modulus at least 1.2 times the modulus of the section it feeds, with enough liquid volume to cover that section’s shrinkage.
- Make freezing directional. Place feeders on the heaviest sections and chills on isolated heavy spots, so metal freezes from the far end back towards the feeder.
- Control gating and pouring. Hold the agreed pouring temperature and fill rate; too hot adds liquid shrinkage, too cold blocks feeding paths.
- Fix the design where you can. Even walls, generous fillets and no isolated heavy lumps. An inscribed-circle check at junctions shows where metal mass collects.
- Prove it on the first-off. Radiograph or section the first castings at the hot spots before releasing lot production.
Shrinkage porosity vs gas porosity: comparison
| Point | Shrinkage porosity | Gas porosity |
|---|---|---|
| Look | Jagged, branching (dendritic) voids | Round holes with smooth, shiny walls |
| Where | Hot spots, thick sections, under feeders, at junctions | Near the top surface, under cores, near chills that were damp |
| Main cause | Not enough liquid feed metal while freezing | Gas from moisture, binders or the melt trapped as metal freezes |
| Main fix | Feeder size and position, chills, design | Dry moulds and cores, venting, degassing, clean charge |
| Best test | Radiography, sectioning, pressure test | Radiography, visual after machining |
How hidden shrinkage is found and graded
| Test | What it shows | Reference used for steel castings |
|---|---|---|
| Radiography (X-ray or gamma) | Internal shrinkage graded by severity level | ASTM E446 (up to 51 mm wall), E186 (51 to 114 mm), E280 (114 to 305 mm) |
| Ultrasonic testing | Internal discontinuities in thick sections | As agreed on the order |
| Pressure or leak test | Through-wall porosity in pump and valve bodies | Test pressure from the drawing or product standard |
| Sectioning | Exact size and spread of porosity in a sample part | First-off approval |
Agree the test method and the acceptance level on the order before the first casting. Without them, “no porosity” cannot be checked.
Shrinkage porosity FAQs (English and Hindi)
Can shrinkage porosity be removed by heat treatment?
No. Heat treatment changes structure and properties but does not close voids. The fix is in feeding, chills and design.
Why does shrinkage show only after machining?
It sits just under the skin at hot spots. When the machining allowance is cut away, the voids open on the machined face.
कास्टिंग में श्रिंकेज पोरोसिटी क्यों होती है?
जब कास्टिंग का आख़िरी जमने वाला हिस्सा फीडर से पिघली धातु नहीं ले पाता, तो वहाँ छोटे, खुरदरे छेद बन जाते हैं। मोटे सेक्शन और जोड़ों पर यह ज़्यादा होता है।
श्रिंकेज पोरोसिटी कैसे रोकें?
सही आकार का फीडर मोटे हिस्से पर लगाएँ, ज़रूरत हो तो चिल लगाएँ, पोरिंग तापमान नियंत्रित रखें और दीवार की मोटाई एक समान रखें। पहली कास्टिंग का रेडियोग्राफी से परीक्षण करें।
Alloynex Foundries, Harmada, Jaipur, makes grey iron, SG iron, steel and alloy steel castings to customer drawings for buyers in Jaipur, Jodhpur, Udaipur, Kota, Ajmer, Bhilwara, Alwar, Bhiwadi, Neemrana and Sikar, across India and for export. Have a part that shows porosity after machining? Send your drawing for a technical review or email info@alloynex.com. Related guides: machining allowance on castings, ISO 8062-3 casting tolerances, heat treatment of castings.
Last updated: 13 November 2026
Related: normalizing vs annealing steel castings and cracking risk and castings for Banswara, Dungarpur and Pratapgarh plants
Related: steel and high manganese castings for Pali and Jalore
Where is the shrinkage? A location-based troubleshooting matrix
Quick answer: Shrinkage porosity forms where metal freezes last without liquid feed, so its location tells you its cause. Porosity at a thick-to-thin junction points to a hot spot; under a riser contact to an undersized feeder; in a machined bore to a core-surrounded heavy section. Match the location to the fix and the test below.
| Where the shrinkage shows | Most likely cause | Foundry fix | Test that confirms it |
|---|---|---|---|
| At a thick-to-thin junction or heavy boss | Isolated hot spot that freezes last | Add a feeder or chill at the hot spot, or even out wall thickness | Radiography or ultrasonic test at the junction; section a sample |
| Just below the riser contact | Feeder too small or freezes before the casting | Larger feeder, insulating or exothermic sleeve, longer feeding neck | Cut-off check of riser contact; dye penetrant after fettling |
| Surface sink on the top (cope) face | Heavy section near the surface with no feed | Feed the section, use a chill below it, adjust pouring temperature | Visual and dimensional check; flatness after machining |
| Along the centreline of a long plate or rib | Long feeding distance, parallel walls freeze together | Taper the wall toward the feeder, add chills to create directional freezing | Radiography along the centreline |
| Inside a machined bore or around a core | Heavy metal wrapped around a core, core overheats | Core with chill or better venting, reduce mass around the bore, add feed path | Machining trial on samples; pressure or leak test |
| Spread as fine porosity in SG iron | Graphite expansion not used for feeding, soft mould walls move | Rigid mould, controlled inoculation and pouring temperature, feeder design for SG iron | Ultrasonic test, density check, microstructure on test piece |
Shrinkage porosity glossary for buyers
| Term | Plain meaning | Why a buyer should care |
|---|---|---|
| Hot spot | The part of a casting that stays liquid longest | Shrinkage forms here unless it is fed or chilled |
| Feeder (riser) | Reservoir of liquid metal that feeds the casting as it shrinks | Too small a feeder leaves cavities under it |
| Chill | Metal insert in the mould that cools a section faster | Moves the last-to-freeze point to where a feeder can reach |
| Directional solidification | Freezing that moves step by step toward the feeder | The design aim that prevents shrinkage |
| Section modulus (casting) | Volume divided by cooling surface; a measure of how slowly a section cools | Thicker, chunkier sections need feeding first |
| Microshrinkage | Very fine scattered pores, often seen only after machining or leak testing | Can cause leaks in pump and valve bodies |
Step-by-step: approving samples without shrinkage
- Mark critical zones on the drawing: pressure walls, sealing faces, bores and heavy bosses.
- Agree the NDT for those zones, for example radiography or ultrasonic test, and the acceptance level.
- Ask the foundry which zones it expects to be hot spots and how it will feed or chill them.
- Section or X-ray the first sample at those zones before machining the full lot.
- Run a machining trial and, for pressure parts, a hydro or leak test on samples.
- Freeze the method (feeders, chills, pouring temperature) once samples pass, and record it for repeat lots.
Share your shrinkage problem and drawing at info@alloynex.com. Alloynex Foundries, Harmada, Jaipur, reviews hot spots and feeding at the drawing stage. Also read machining allowance on castings.
Last updated: 14 November 2026
Casting defects glossary: plain-language meanings for buyers
Short answer: A casting defect is any flaw in shape, surface or soundness that breaks the drawing or the standard. Buyers mainly meet gas defects (blowholes, pinholes), shrinkage, inclusions, cold shuts and cracks. Knowing the right name helps you write a clear rejection note and agree the right test, such as radiography, ultrasonic testing or dye penetrant.
| Term | What it means | Usual check |
|---|---|---|
| Blowhole | A smooth, round gas cavity near the surface, often from moist sand or poor venting. | Visual, RT |
| Pinhole porosity | Many tiny gas holes just under the skin, often from hydrogen or nitrogen picked up in the melt. | UT or RT; visual after machining |
| Shrinkage cavity | A rough, jagged void where the last metal to freeze could not be fed. Found at heavy sections. | RT or UT; cut section on samples |
| Hot tear | An irregular crack formed while the metal is still weak and hot, usually at sharp corners in steel castings. | DPT or MPI |
| Cold shut | A seam where two metal streams met but did not fuse, from low pouring temperature or slow filling. | Visual, DPT |
| Misrun | A casting that did not fill completely, often in thin walls. | Visual |
| Sand inclusion | Mould or core sand trapped in the metal; seen after machining or shot blasting. | Visual after machining or shot blasting |
| Slag inclusion | Non-metallic slag trapped in the casting, from poor skimming or no filter. | Visual, RT |
| Scab / buckle | A rough raised patch where the mould face cracked and metal ran behind it. | Visual |
| Mismatch (shift) | A step at the parting line where cope and drag were not aligned. | Dimensional check |
| Chill (in grey iron) | Hard white iron at thin edges or corners, from fast cooling; hard to machine. | Hardness at edges, visual after machining |
| Dross (in SG iron) | Oxide films from magnesium treatment that weaken SG iron near the top surface. | Visual, microstructure near top face |
Quotable fact: shrinkage cavities are rough and branched, while gas blowholes are smooth and round; this one look tells the foundry whether to fix feeding or fix venting and sand moisture. Alloynex Foundries, Jaipur, reviews defect reports for grey iron (IS 210), SG iron (IS 1865) and steel castings (IS 1030).
Related: grey iron castings for Rajsamand plants | casting design tips | heat treatment of castings
Send your drawing for a technical review: info@alloynex.com. Last updated: 15 Nov 2026
Worked example: how is a porosity defect in a pump casing traced and stopped?
A porosity defect is traced in 5 steps: locate it on the part, find where it sits in the mould, check the melt and sand records for that heat, change one cause at a time, and prove the fix with a pressure test and a cut section. This worked example uses a grey iron pump casing, but the same method works for SG iron and steel castings.
The case
A buyer finds small round holes on the machined face of an IS 210 FG 260 pump casing. Three castings out of twenty leak on the pressure test.
| Step | What is done | What it shows |
|---|---|---|
| 1. Locate | Mark the holes on the drawing | Holes sit near the top face, below the riser |
| 2. Shape | Look at the hole surface | Smooth and shiny walls point to gas porosity; rough, jagged walls point to shrinkage |
| 3. Records | Check sand moisture, pouring temperature and core venting for that heat | Core vents were partly blocked |
| 4. One change | Open core vents and add a vent in the core print | Gas from the core can now escape |
| 5. Prove | Pressure test the next lot and cut one casting through the face | No leak, no holes in the section |
Quotable fact: gas porosity usually shows smooth, round holes near upper surfaces, while shrinkage porosity shows rough, branching cavities in the last part of the casting to freeze.
Gas porosity vs shrinkage: quick comparison
| Point | Gas porosity | Shrinkage porosity |
|---|---|---|
| Look | Round, smooth, shiny | Jagged, branching, dull |
| Where | Near top surfaces and cores | Thick sections and hot spots |
| Usual fix | Venting, sand moisture, melt cleanliness | Feeding, riser size, chills, design change |
FAQs
How do you tell gas porosity from shrinkage?
Gas holes are round and smooth near upper surfaces; shrinkage cavities are rough and branching in thick sections that freeze last.
What test proves a leak fix on a pump casing?
A pressure test at the value written on the drawing, plus one cut section through the problem area.
कास्टिंग में गैस पोरोसिटी कैसे पहचानें?
गैस के छेद गोल और चिकने होते हैं और अक्सर ऊपरी सतह या कोर के पास मिलते हैं।
श्रिंकेज पोरोसिटी कैसे रोकी जाती है?
राइज़र का सही साइज़, फीडिंग, चिल और ज़रूरत हो तो डिज़ाइन में बदलाव से।
Related: casting design tips, IS 210 grey iron grades, valve body castings.
Send your drawing for a technical review, or request a metallurgy consultation, at info@alloynex.com.
Last updated: 16 Nov 2026