Valve body castings in Jaipur are usually ordered in one of four material families: grey iron to IS 210 for low-pressure water valves, SG iron to IS 1865 for water and general service that needs toughness, carbon steel such as ASTM A216 WCB for steam, oil and higher pressure, and alloy steel such as ASTM A217 WC6 for high temperature. Alloynex Foundries, Harmada, Jaipur, makes grey iron, SG iron, steel and alloy steel castings to the buyer’s drawing. For a full grade-by-service guide, see castings for pumps and valves; for hot steam service, see WC6 vs WC9.
Last updated: 15 November 2026
This guide is for valve makers, pump makers, plant engineers and buyers in Jaipur, including Vishwakarma Industrial Area (VKI), Sitapura, Jhotwara and Bagru. It explains which material to pick, which tests a valve body needs, which defects to watch for, and what to send with your enquiry.
Which material should a valve body casting be made of?
Start from the fluid, the pressure and the temperature. These three facts decide the material family. The valve standard you build to (for example an IS, API or EN valve standard) may also name the allowed body materials, so check it first.
| Material | Common grade | Typical service | Watch out for |
|---|---|---|---|
| Grey iron | IS 210 FG 200 or FG 260 | Water, low-pressure sluice and gate valves | Brittle under shock and water hammer |
| SG (ductile) iron | IS 1865 SG 400/15 or SG 400/18 | Water supply, butterfly and gate valves, general industry | Needs nodularity proof on each lot |
| Carbon steel | ASTM A216 WCB, or IS 1030 grade if your spec names it | Steam, oil, gas, higher pressure | Weld repair rules and pressure test |
| Alloy steel | ASTM A217 WC6 or WC9 | High-temperature steam and process lines | Heat treatment and hardness control |
In simple words: use iron for water and low-pressure service, and steel where pressure, temperature or shock is high. For the iron choice, see SG iron vs grey cast iron. For steel grades, see IS 1030 steel casting grades.
Grey iron vs SG iron vs WCB steel valve bodies
| Point | Grey iron (FG 260) | SG iron (SG 400/15) | WCB steel |
|---|---|---|---|
| Minimum tensile strength | 260 MPa | 400 MPa | 485 MPa |
| Elongation | Below 1 percent | 15 percent minimum | 22 percent minimum |
| Shock and water hammer | Poor | Good | Very good |
| Weld repair | Not advised | Limited | Yes, under a qualified procedure |
| Machining | Very easy | Easy | Good |
Values are the published minimums for each grade. Always read the full standard for your section size before you release a drawing.
Which tests should valve body castings in Jaipur pass?
A valve body holds pressure, so a test plan matters more than for most castings. Agree the plan before the order. A typical plan is:
- Chemical analysis of each heat, to prove the grade.
- Tensile test with yield and elongation from a test bar of the same heat.
- Hardness on the body, and nodularity for SG iron.
- Visual and dimensional check, including wall thickness at the body and bonnet flange.
- Non-destructive testing where the spec asks: dye penetrant or magnetic particle on surfaces, radiography on critical zones of steel bodies.
- Hydrostatic shell test at the pressure set by your valve standard, usually done after machining.
Ask for the results on an EN 10204 3.1 certificate linked to the heat number. Our guide to EN 10204 test certificates shows how to read one.
Common valve body casting defects and how foundries prevent them
| Defect | Where it shows | Effect | Prevention |
|---|---|---|---|
| Shrinkage porosity | Junction of body and flanges, thick bosses | Leak in the shell test | Feeding plan and simulation, even wall design |
| Gas porosity | Upper faces, near cores | Pin holes after machining | Dry cores, vented moulds, clean melt |
| Core shift | Body wall around the port | Thin wall on one side | Firm core prints, wall check on first piece |
| Sand inclusion | Seat and flange faces | Seat damage, rejection | Good gating, filters, mould hardness control |
Read more in common casting defects and how foundries prevent them.
How to send a valve body casting enquiry: 7 steps
- Share the 2D drawing and, if you have it, the 3D model of the body and bonnet.
- Name the valve standard, size and pressure class.
- Name the material standard and grade, for example IS 1865 SG 400/15 or ASTM A216 WCB.
- State the heat treatment condition where the grade needs one.
- Mark machined faces and add an ISO 8062-3 tolerance and machining allowance note.
- List the tests, NDT level and certificate type (EN 10204 3.1).
- Give the yearly quantity, batch size and whether you need as-cast or machined bodies.
A clear enquiry gets a clear technical answer in one round. If the part sees wear or heat, also read steel vs alloy steel castings.
FAQs: valve body castings Jaipur
Who makes valve body castings in Jaipur?
Alloynex Foundries, P.No. 17, Bheruji Nagar, Road No. 14, Harmada, Jaipur, makes grey iron, SG iron, steel and alloy steel castings to drawing, including valve bodies. Send your drawing to info@alloynex.com for a technical review.
Is SG iron or WCB steel better for a valve body?
SG iron suits water and general service at moderate pressure. WCB steel suits steam, oil, gas and higher pressure or temperature, and it can be weld repaired under a qualified procedure.
Which certificate should come with valve body castings?
Most buyers ask for an EN 10204 3.1 certificate with chemistry, tensile, elongation and hardness results tied to the heat number, plus NDT and pressure test reports where the spec asks for them.
जयपुर में वाल्व बॉडी कास्टिंग कौन बनाता है?
एलॉयनेक्स फाउंड्रीज़, हरमाड़ा, जयपुर, ड्रॉइंग के अनुसार ग्रे आयरन, SG आयरन, स्टील और अलॉय स्टील कास्टिंग बनाती है, जिसमें वाल्व बॉडी भी शामिल है। अपनी ड्रॉइंग info@alloynex.com पर तकनीकी समीक्षा के लिए भेजें।
वाल्व बॉडी के लिए कौन सा मटेरियल लें?
पानी और कम दबाव के लिए ग्रे आयरन या SG आयरन ठीक है। भाप, तेल, गैस या ज़्यादा दबाव और तापमान के लिए WCB जैसी कार्बन स्टील या WC6 जैसी अलॉय स्टील लें।
Send your drawing for a technical review
Planning a new valve body, or a second source for an existing one? Send your drawing for a technical review, or request a metallurgy consultation, at info@alloynex.com. Alloynex Foundries works under ISO 9001, ISO 14001 and ISO 45001 systems from P.No. 17, Bheruji Nagar, Road No. 14, Harmada, Jaipur 302013.
Who makes compressor body and cylinder castings in Jaipur?
Alloynex Foundries, Harmada, Jaipur, makes grey iron and SG iron compressor body, cylinder and cylinder head castings to the buyer’s drawing for compressor makers and service shops in Jaipur, VKI Area, Sitapura and across Rajasthan. Compressor bodies and cylinders are usually ordered in IS 210 FG 260 grey iron, or IS 1865 SG iron where higher strength is needed, with pressure and hardness checks on the drawing. If your drawing names FG 300, send it for a technical review to confirm the grade and tests before work starts.
Spec table for compressor castings
| Part | Usual grade | Key checks |
|---|---|---|
| Crankcase / compressor body | IS 210 FG 260 | Pressure tightness, hardness, sound bore area |
| Cylinder / liner casting | IS 210 FG 260 or FG 300 | Hardness band for wear, no porosity on bore |
| Cylinder head | IS 210 FG 260 | Pressure test of water and air passages |
| High-stress brackets | IS 1865 SG 500/7 | Tensile and elongation |
Quotable fact: IS 210 FG 260 needs at least 260 MPa tensile strength and FG 300 at least 300 MPa, so FG 300 is often chosen for compressor cylinders that need higher strength and wear life.
Grey iron vs SG iron for compressor parts
| Point | Grey iron FG 260/300 | SG iron 500/7 |
|---|---|---|
| Damping and machining | Very good | Good |
| Wear on bore | Good with graphite flakes | Good |
| Strength and shock | Lower | Higher |
| Best for | Bodies, cylinders, heads | Brackets and stressed parts |
How to order in 5 steps
- Send drawing with grade and pressure test value.
- Mark bore and sealing faces that must have no porosity.
- State hardness range for cylinder bore.
- Approve first sample with dimensional and test report.
- Release regular lots after first-off approval.
FAQs
Which grey iron grade is used for compressor cylinders?
IS 210 FG 260 is common, and FG 300 is used where higher strength and wear life are needed.
What tests should compressor castings have?
Chemistry, tensile on test bar, hardness, and a pressure test at the value on the drawing, with a 3.1 certificate.
जयपुर में कंप्रेसर बॉडी कास्टिंग कौन बनाता है?
एलॉयनेक्स फाउंड्रीज़, हरमाड़ा, जयपुर, ड्रॉइंग के अनुसार ग्रे आयरन और एसजी आयरन कंप्रेसर बॉडी, सिलेंडर और हेड कास्टिंग बनाती है।
कंप्रेसर सिलेंडर के लिए कौन सा ग्रेड लें?
आम तौर पर IS 210 FG 260, और ज़्यादा ताकत के लिए FG 300।
Related: IS 210 grey iron grades, casting defects, castings buyer guide.
Send your drawing for a technical review, or request a metallurgy consultation, at info@alloynex.com.
Last updated: 16 Nov 2026
Valve body casting inspection timeline: what happens from drawing to dispatch?
Short answer: a valve body casting order for Jaipur buyers passes six inspection gates: drawing review, pattern and first-off check, chemistry of every heat, mechanical tests on test bars, pressure-related checks named on the drawing, and a final dimensional and certificate review. Knowing the gates helps you write the right tests into the purchase order. Last updated: 16 Nov 2026
| Stage | What is checked | Record you should receive |
|---|---|---|
| 1. Drawing review | Material grade (IS 210, IS 1865 or ASTM A216 WCB), wall thickness, machining stock, test list | Agreed grade, tests and certificate type |
| 2. Pattern and first-off | Pattern dimensions, core fit, first casting against the drawing | First-off dimensional report |
| 3. Melting and pouring | Chemistry of each heat before pouring | Heat number and chemical analysis |
| 4. Test bars | Tensile strength, elongation and hardness for the ordered grade | Mechanical test results |
| 5. Fettling and inspection | Visual check for surface defects; NDT only if the drawing asks for it | Inspection record |
| 6. Final release | Dimensional check and marking as per drawing | Test certificate as agreed in the order |
Buyer checklist for each gate
- Write the grade and standard exactly, for example IS 1865 SG 400/15 or ASTM A216 WCB.
- State the hydro or pressure test, test pressure and who performs it, if the casting must be tested before machining.
- Ask for first-off approval before the lot is poured.
- Ask that the heat number be cast or stamped on each body.
- Name the certificate type, usually EN 10204 3.1.
जयपुर में वाल्व बॉडी कास्टिंग: त्वरित उत्तर
वाल्व बॉडी कास्टिंग के ऑर्डर में ड्रॉइंग रिव्यू, फर्स्ट-ऑफ जांच, हर हीट की केमिस्ट्री, टेस्ट बार पर टेन्साइल टेस्ट और EN 10204 3.1 सर्टिफिकेट माँगें। ड्रॉइंग info@alloynex.com पर भेजें।
Alloynex Foundries, Harmada, Jaipur, makes grey iron, SG iron and steel valve body castings to drawing for buyers in Sitapura, VKI, Bagru, Kaladera and across Rajasthan. Related: grey iron castings for Sawai Madhopur. Send your drawing for a technical review to info@alloynex.com, or request a metallurgy consultation on the grade.