Machining allowance on castings is the extra metal a foundry leaves on surfaces that will be machined later, so that the final part reaches its exact size and a clean, sound finish. Getting this allowance right saves machining time, avoids scrap and protects the strength of the finished component.
This guide explains machining allowance in simple terms for OEM engineers, QA teams and buyers. It covers why the allowance exists, what decides its size, how standards describe it, and how to show it clearly on your drawing.
What machining allowance means
A casting comes out of the mould close to its final shape, but not exact. The surface may carry a thin skin of scale, sand or small surface flaws. Some faces also need a tight size, a smooth finish or a precise fit with other parts.
To reach these needs, the casting is made a little larger on those faces. The machinist then removes this extra layer. That extra layer is the machining allowance. Faces that stay as-cast need no allowance at all.
Why castings need machining allowance
There are four main reasons.
- To remove the outer skin, which may hold scale, sand or fine porosity
- To correct small size changes from shrinkage and mould movement
- To reach tight tolerances, flatness and surface finish needed for fits and seals
- To give the machinist a clean starting surface for clamping and datum setting
Too little allowance can leave black spots or skin on a machined face, and the part may be rejected. Too much allowance wastes metal and machining hours, and can expose hidden defects deep inside thick sections.
What decides the size of the allowance
No single number fits every casting. The right allowance depends on several factors working together.
| Factor | Effect on allowance |
|---|---|
| Overall casting size | Larger castings usually need more allowance |
| Metal type | Grey iron, SG iron and steel shrink and behave differently |
| Moulding process | Precise processes allow smaller allowance than open sand moulds |
| Position in the mould | Top faces often need more, as impurities rise upward |
| Required finish and tolerance | Tighter needs may call for a little more stock |
| Heat treatment | Parts that may distort during treatment need extra margin |
Metal choice matters a lot. Our guides on SG iron vs grey cast iron and steel vs alloy steel castings explain how these materials differ in shrinkage and machinability.
How standards describe machining allowance
Many buyers refer to ISO 8062-3. This standard sets out casting dimensional tolerance grades, called DCTG, and required machining allowance grades, called RMA grades, marked by letters from A to K. A lower letter means a smaller allowance, and a higher letter means a larger one.
Using a standard grade on the drawing gives both sides a common language. The foundry knows exactly how much stock to leave, and the buyer knows what to expect at incoming inspection. When no grade is given, agree the allowance in writing before the pattern is made.
Allowance, tolerance and draft: three different things
These three ideas are often mixed up, so it helps to separate them.
Machining allowance is extra metal added on purpose for machining. Dimensional tolerance is the allowed variation in size of the raw casting. Draft is the small taper on vertical faces that lets the pattern come out of the mould cleanly.
A machined face must have enough allowance to cover the tolerance and the draft. If the draft or tolerance eats into the allowance, the machinist may not clean up the face fully.
Machining allowance and casting defects
Allowance is closely linked to casting soundness. Small gas holes or sand marks near the surface are often removed with the allowance. But if the allowance is too large, the cut may reach shrinkage cavities in the middle of a thick section. This can turn a sound-looking casting into a reject after machining.
Good method design, correct feeding and steady pouring keep the zone under the machined face clean. Our guide to common casting defects and their prevention explains this in more detail. Heat treatment can also shift size slightly, which is why distortion margin is part of the allowance plan.
Tips for showing machining allowance on your drawing
- Mark every machined face clearly with a machining symbol
- State the required machining allowance grade, or the stock in writing
- Show datum faces and locating points for the first machining set-up
- Note any faces that must stay as-cast
- Share the finished machined drawing as well as the casting drawing
- Agree inspection points, such as checking stock on sample castings
A short design review before tooling is made catches most allowance problems. It is far easier to adjust a pattern on paper than to rework it later.
Benefits of getting machining allowance right
When the allowance is correct, machining time drops, tool wear falls and scrap from black spots disappears. Weight stays under control, which also helps with freight for export parts. Most importantly, the finished part keeps the strength and soundness the design needs.
Alloynex works to ISO 9001, ISO 14001 and ISO 45001 systems and supports buyers with grey iron, SG iron, steel and alloy steel castings. You can learn more about our casting services.
FAQs
What is machining allowance in casting?
It is the extra metal left on faces that will be machined, so the finished part reaches its exact size and a clean surface after machining.
Is machining allowance the same as tolerance?
No. Allowance is extra metal added on purpose. Tolerance is the permitted variation in the raw casting size. Both must be planned together.
Which standard covers machining allowance for castings?
ISO 8062-3 is widely used. It defines required machining allowance grades from A to K and dimensional tolerance grades for castings.
Why do top faces of a casting need more allowance?
During pouring, lighter impurities and gas tend to rise. The top face may carry more of these, so extra stock helps the machinist reach clean metal.
What happens if the allowance is too small?
The machined face may not clean up fully. Black skin or surface flaws can remain, and the part may fail inspection.
Get your casting drawing reviewed
Unsure how much machining allowance your part needs? Send your drawing for a technical review. Our engineers will check allowance, draft and datum points before tooling starts. Write to info@alloynex.com or request a metallurgy consultation.
How much machining allowance should you keep on a sand casting?
Short answer: for grey iron and SG iron sand castings, a common starting point is about 2.5 to 3 mm per machined face on small parts, 3 to 5 mm on medium parts and 5 to 8 mm on large parts. Top (cope) faces and steel castings usually need more. The final value should come from an ISO 8062-3 RMA grade on your drawing.
Machining allowance is extra metal, not a tolerance. Too little leaves black skin on the machined face. Too much wastes metal and machining time and can open up hidden porosity.
Typical starting values (sand castings, per face)
| Longest side of the casting | Grey iron / SG iron | Carbon and alloy steel | Notes |
|---|---|---|---|
| Up to about 300 mm | 2.5 to 3 mm | 3 to 4 mm | Small cored bores often 2 to 3 mm on radius |
| About 300 to 800 mm | 3 to 5 mm | 4 to 6 mm | Add 1 to 2 mm on the top (cope) face |
| Above about 800 mm | 5 to 8 mm | 6 to 10 mm | Check distortion after heat treatment |
5 steps to set the allowance on your drawing
- Mark every machined face clearly, with its finish symbol.
- Choose the dimensional tolerance grade (DCTG) and the RMA grade from ISO 8062-3.
- Give machining datums (locating points) so the foundry and machinist work from the same faces.
- Note the metal and grade, for example IS 210 FG 260 or IS 1865 SG 500/7, because steel and iron need different stock.
- Ask for a first-off casting check: machine one piece and confirm every face cleans up before lot production.
Iron vs steel castings: why the allowance differs
| Point | Grey iron and SG iron | Steel and alloy steel |
|---|---|---|
| Shrinkage during cooling | Lower | Higher, more risk of size change |
| Surface skin and scale | Thin | Thicker, plus scale after heat treatment |
| Distortion risk | Lower | Higher after normalising or hardening |
| Usual allowance | Base value | About 1 to 2 mm more than iron on the same size |
How much machining allowance does a grey iron sand casting need?
A small grey iron sand casting usually needs about 2.5 to 3 mm per machined face. Medium parts need about 3 to 5 mm, and the top face often gets 1 to 2 mm extra. Confirm the value with the RMA grade on your drawing.
Do steel castings need more allowance than cast iron?
Yes, in most cases. Steel shrinks more, forms thicker scale and can distort during heat treatment, so foundries usually leave about 1 to 2 mm more stock than on an iron casting of the same size.
कास्टिंग में मशीनिंग अलाउंस कितना रखना चाहिए?
ग्रे आयरन और एसजी आयरन की सैंड कास्टिंग में छोटे पार्ट पर लगभग 2.5 से 3 मिमी, मध्यम पार्ट पर 3 से 5 मिमी और बड़े पार्ट पर 5 से 8 मिमी प्रति फेस रखा जाता है। स्टील कास्टिंग में थोड़ा ज़्यादा रखें। अंतिम मान ड्रॉइंग पर ISO 8062-3 RMA ग्रेड से तय करें।
Buyers we support: Alloynex Foundries, Harmada, Jaipur, reviews casting drawings for buyers in Jaipur, Jodhpur, Udaipur, Kota, Ajmer, Bhilwara, Alwar, Bhiwadi, Neemrana, Sikar and Pali, across India and for export. Send your drawing for a technical review at info@alloynex.com.
Related: SG iron vs grey cast iron, common casting defects, EN 10204 test certificates, castings buyer guide for Rajasthan, our casting services.
Last updated: 13 November 2026
Related: SG iron castings for Bhilwara buyers
How much machining allowance does each ISO 8062-3 RMA grade give?
Direct answer: ISO 8062-3 sets the required machining allowance (RMA) from two inputs: the greatest overall dimension of the casting and an RMA grade from A (least stock) to K (most stock). For example, a casting whose greatest dimension is 250 to 400 mm gets 2.5 mm per machined face at grade F and 5 mm at grade H. The casting tolerance is then added on top.
RMA values by grade (mm per machined surface)
| Greatest casting dimension (mm) | A | B | C | D | E | F | G | H | J | K |
|---|---|---|---|---|---|---|---|---|---|---|
| up to 40 | 0.1 | 0.1 | 0.2 | 0.3 | 0.4 | 0.5 | 0.5 | 0.7 | 1 | 1.4 |
| over 40 to 63 | 0.1 | 0.2 | 0.3 | 0.3 | 0.4 | 0.5 | 0.7 | 1 | 1.4 | 2 |
| over 63 to 100 | 0.2 | 0.3 | 0.4 | 0.5 | 0.7 | 1 | 1.4 | 2 | 2.8 | 4 |
| over 100 to 160 | 0.3 | 0.4 | 0.5 | 0.8 | 1.1 | 1.5 | 2.2 | 3 | 4 | 6 |
| over 160 to 250 | 0.3 | 0.5 | 0.7 | 1 | 1.4 | 2 | 2.8 | 4 | 5.5 | 8 |
| over 250 to 400 | 0.4 | 0.7 | 0.9 | 1.3 | 1.8 | 2.5 | 3.5 | 5 | 7 | 10 |
| over 400 to 630 | 0.5 | 0.8 | 1.1 | 1.5 | 2.2 | 3 | 4 | 6 | 9 | 12 |
| over 630 to 1000 | 0.6 | 0.9 | 1.2 | 1.8 | 2.5 | 3.5 | 5 | 7 | 10 | 14 |
Values as commonly published from ISO 8062-3 (carried over from ISO 8062:1994). Confirm against your licensed copy of the standard before release. One RMA value applies to all machined faces of the casting unless the drawing gives a separate value for a face.
Typical RMA grades by process (sand castings)
| Process | Steel | Grey iron | SG iron |
|---|---|---|---|
| Sand, hand moulded | G to K | F to H | F to H |
| Sand, machine moulded or shell | F to H | E to G | E to G |
These are typical ranges only. The foundry confirms the grade at drawing review after looking at the part shape, the top (cope) faces and the machining datum.
How to work out the raw casting size: 5 steps
- Find the greatest overall dimension of the casting and read the RMA row.
- Pick the RMA grade for the process and metal (table above), then read RMA.
- Pick the DCTG grade and read the total tolerance (DCT) for the dimension you are sizing. See ISO 8062-3 casting tolerances explained.
- For an outside size machined both sides: R = F + 2 × RMA + DCT/2. For a bore machined both sides: R = F − 2 × RMA − DCT/2.
- Write it on the drawing, for example: General tolerances ISO 8062-3 – DCTG 11 – RMA 5 (RMAG H).
Worked example: a grey iron flange, finished outside diameter 300 mm, greatest dimension 300 mm, RMAG H gives RMA 5 mm; DCTG 11 for 250 to 400 mm gives a total band of 6.2 mm. Raw diameter R = 300 + 2 × 5 + 6.2/2 = 313.1 mm.
RMA vs DCTG vs draft: comparison
| Item | What it is | Who sets it | On the drawing |
|---|---|---|---|
| RMA | Extra metal left on a face that will be machined | Buyer by grade, foundry confirms | RMA value with RMAG letter |
| DCTG | Permitted variation of the raw cast size | Process capability | General casting tolerance grade |
| Draft | Taper on walls so the pattern leaves the mould | Foundry pattern design | Draft angle, or “draft to foundry standard” |
ISO 8062 RMA FAQs (English and Hindi)
What does RMAG H mean on a drawing?
It means required machining allowance grade H. Read the RMA value from the H column for the greatest casting dimension, for example 5 mm for 250 to 400 mm.
Is RMA per side or on diameter?
Per machined surface. A diameter machined on both sides gets two times RMA plus half the casting tolerance.
ISO 8062-3 में RMA ग्रेड क्या है?
RMA ग्रेड A से K तक होता है। A में सबसे कम और K में सबसे ज़्यादा मशीनिंग स्टॉक होता है। मान कास्टिंग के सबसे बड़े आयाम से तय होता है।
ड्रॉइंग पर मशीनिंग अलाउंस कैसे लिखें?
टाइटल ब्लॉक में लिखें: “General tolerances ISO 8062-3 – DCTG 11 – RMA 5 (RMAG H)”। मशीन होने वाले फेस साफ़ दिखाएँ।
Alloynex Foundries, Harmada, Jaipur, makes grey iron, SG iron, steel and alloy steel castings to customer drawings for buyers in Jaipur, Jodhpur, Udaipur, Kota, Ajmer, Bhilwara, Alwar, Bhiwadi, Neemrana and Sikar, across India and for export. Send your drawing for a technical review and we will confirm RMA, DCTG, draft and datum points before pattern work. Related: casting defects and prevention, castings buyer guide for Rajasthan.
Last updated: 13 November 2026
Related: FG 200 vs FG 260 vs FG 300 grey iron grades and grey iron castings for Kishangarh marble machinery
Feature-by-feature machining allowance: a decision matrix
Quick answer: Machining allowance is not one number for the whole casting. Start from the ISO 8062-3 RMA grade for the casting’s greatest dimension, then add margin on features that carry more risk: top (cope) faces, cored bores, faces near heavy sections and parts that distort in heat treatment. The matrix shows how to treat each feature.
| Feature on the drawing | Risk if stock is short | How to set the allowance | What to write |
|---|---|---|---|
| Bottom (drag) face, flat | Low; cleanest face in the mould | Base RMA value for the grade | RMA per ISO 8062-3, RMAG letter |
| Top (cope) face | Slag, sand and gas rise to the top | Base RMA plus extra margin agreed with the foundry | Separate note for the cope face, or a local RMA value |
| Cored bore | Core shift and rough core surface | Base RMA on radius plus core shift margin; check minimum bore that will clean up | Bore as-cast diameter and RMA on radius |
| Face next to a heavy boss | Hidden shrinkage just below the skin | Normal RMA, but ask for NDT or sample sectioning in that zone | Critical zone note on the drawing |
| Faces on parts that are heat treated | Distortion after normalising or hardening | Add margin for distortion; machine after heat treatment | Machining stage and heat treatment sequence |
| Sealing or bearing faces | Porosity exposed after machining | Normal RMA plus leak or pressure test after machining | Surface finish, test requirement |
Machining allowance glossary
| Term | Plain meaning |
|---|---|
| RMA | Required machining allowance: extra metal on one machined surface, per ISO 8062-3 |
| RMAG | RMA grade, letters A to K; a higher letter gives more stock |
| DCTG | Dimensional casting tolerance grade: allowed variation of raw cast size |
| Cope and drag | Top and bottom halves of a sand mould |
| Clean-up | Machining deep enough to remove all as-cast skin with no black spots |
| Datum | Reference face or point from which the casting is set up for machining |
Checklist before you release the drawing
- Mark every machined face and give the RMA grade or value.
- Flag the cope face, cored bores and heavy-section faces for extra margin.
- Name casting datums the machine shop can use for the first setup.
- State whether machining is before or after heat treatment.
- Agree the DCTG so the raw size stays inside the allowance.
- Ask for a first-article machining trial on samples.
Send your drawing for a technical review at info@alloynex.com. Related: common casting defects and prevention.
Last updated: 14 November 2026
Related: casting design tips: 8 simple rules for better castings
Related district guides: SG iron castings for Beawar and Ajmer, grey iron castings for Balotra and Barmer and ductile iron castings for Jhalawar and Baran.
Machining allowance glossary: the terms on a casting drawing
Short answer: Machining allowance is the extra metal left on a casting face so it can be machined to final size. ISO 8062-3 gives it as an RMA grade (A to K), and as-cast size tolerance as a DCTG grade (1 to 16). Writing both, plus machining datums, lets the foundry build the right pattern the first time.
| Term | Meaning | Example on a drawing |
|---|---|---|
| RMA (required machining allowance) | Extra metal added per machined face, chosen by grade and the biggest overall casting dimension (ISO 8062-3). | “RMA: ISO 8062-3 grade H” |
| DCTG | Dimensional casting tolerance grade for as-cast sizes; lower number means tighter. | “General tolerance ISO 8062-3 DCTG 11” |
| GCTG | Geometrical casting tolerance grade for flatness, straightness and similar. | “GCTG 7” |
| Datum (A, B, C) | Reference faces the machinist sets up from; must be on sound as-cast or pre-machined faces. | Datum symbols on two or three faces |
| As-cast face | A face left unmachined; carries only the casting tolerance. | No machining symbol |
| Raw casting size | Finished size plus allowance plus tolerance; this is what the pattern produces. | Shown on the casting drawing, not the part drawing |
| Proof machining | Light first cut to reveal subsurface defects before final machining. | “Proof machine faces X and Y” |
| Draft | Taper on vertical faces so the pattern can be drawn from the mould; separate from allowance. | “Draft 1 to 2 degrees, added on” |
Quotable fact: under ISO 8062-3, a larger casting and a looser RMA grade both increase allowance, so a 1 m casting needs more stock per face than a 100 mm casting in the same grade. Alloynex Foundries, Jaipur, checks allowances on grey iron, SG iron and steel casting drawings in its technical review.
Related: IS 1865 SG iron castings for Khairthal-Tijara | grey iron castings for Rajsamand | ISO 8062 casting tolerances
Send your drawing for a technical review: info@alloynex.com. Last updated: 15 Nov 2026
RFQ template: how to write machining allowance on a casting enquiry
Short answer: put the tolerance grade, the machining allowance grade and the machined faces in one note on the drawing, for example “General tolerances ISO 8062-3 DCTG 10, RMA grade H, machined faces marked with the machining symbol”. Then every foundry quotes the same casting.
Copy-and-fill RFQ lines
| Field | What to write | Example |
|---|---|---|
| Part name and number | As on your drawing | Gear housing, rev C |
| Material grade | Standard and grade | IS 210 FG 260 |
| Tolerance grade | ISO 8062-3 DCTG | DCTG 10 (sand cast) |
| Machining allowance | ISO 8062-3 RMA grade | RMA grade H |
| Machined faces | Marked on drawing | Base, bore, top face |
| Datums | First machining set-up | A = base, B = bore axis |
| Supply state | As-cast, rough or finish machined | Rough machined |
| Tests and certificate | List | Chemistry, tensile, hardness, EN 10204 3.1 |
| Quantity | Yearly and per batch | As per plan |
Three mistakes this template avoids
- No RMA grade: each foundry adds a different stock, so quotes cannot be compared.
- No datums: the machinist picks a face that is not the one you planned.
- Tolerance and allowance mixed up: tolerance is how much size may vary; allowance is extra metal for cutting.
Related: SG iron vs grey cast iron, castings sourcing guide, textile machinery castings for Bhilwara.
Send your drawing for a technical review, or request a metallurgy consultation, at info@alloynex.com.
Last updated: 16 Nov 2026