Kota buyers who need grey iron or SG iron castings can source them to drawing from Alloynex Foundries, a cast iron foundry in Harmada, Jaipur. You send the drawing and grade, and the castings come with heat treatment as your part needs.
This guide explains, in simple words, how a plant in Kota can choose the right cast iron, which grades to write on the drawing, what tests to ask for and how to send a clear enquiry. It is written for design engineers, maintenance heads and purchase teams.
What does a cast iron foundry for Kota buyers need to deliver?
Kota and the nearby industrial areas have power, chemical, fertiliser, cement-linked and general engineering units. These plants use many cast iron parts: pump bodies, impellers, valve bodies, motor bodies, gearbox housings, bearing housings, covers, pulleys, liners and machine bases.
For these parts, a good foundry partner must do four things well:
- Read the drawing and grade with care before work starts.
- Control melting and chemistry so every heat meets the grade.
- Test the metal and record the results against each heat.
- Machine and heat treat the part when the drawing asks for it.
Use these four points to compare foundries. Alloynex works under ISO 9001, ISO 14001 and ISO 45001 management systems. You can see the full scope on our casting services page and in our castings buyer guide for Rajasthan.
Grey iron or SG iron: which one fits your Kota plant?
Most cast iron parts are made in one of two families. Grey iron has graphite in the shape of flakes. SG iron, also called ductile iron, has graphite in the shape of small balls. This one difference changes how the part behaves.
| Point | Grey iron (IS 210) | SG iron (IS 1865) |
|---|---|---|
| Graphite shape | Flakes | Round nodules |
| Strength in tension | Lower | Higher |
| Shock and impact | Can crack | Bends before it breaks |
| Vibration damping | Excellent | Moderate |
| Machining | Very easy | Good |
| Typical Kota uses | Pump and motor bodies, bases, covers | Valve bodies, brackets, hubs, pressure parts |
A simple rule: if the part takes shock, pressure or bending, choose SG iron. If it must absorb vibration and needs a lot of machining, grey iron is often the better fit. Our SG iron vs grey cast iron guide explains this in more detail.
Which grades should you write on the drawing?
Always write one standard and one grade. “Cast iron” alone is not enough, because it can mean many different materials. Here are the grades most buyers use, shown as general education:
- Grey iron, IS 210: FG 150, FG 200, FG 220, FG 260, FG 300, FG 350 and FG 400. The number is the minimum tensile strength in MPa. FG 200 and FG 260 are very common for pump bodies, housings and covers.
- SG iron, IS 1865: SG 400/15, SG 450/10, SG 500/7, SG 600/3 and SG 700/2. The first number is the minimum tensile strength in MPa and the second is the minimum elongation in percent.
- Export drawings may use EN 1561 (grey iron, for example EN-GJL-250) or EN 1563 (SG iron, for example EN-GJS-500-7). Name the exact standard used on your drawing.
What tests should a cast iron foundry run?
A grade on paper means little without testing. Ask your foundry to agree on these checks before the first lot:
- Chemical analysis of each heat.
- Tensile test on a test bar cast with the parts.
- Hardness test on the casting.
- Microstructure check, including nodularity for SG iron.
- Dimensional inspection against the drawing.
- Pressure or leak test for pump and valve bodies, if the drawing needs it.
Ask for the results on a test certificate, for example an EN 10204 3.1 certificate. Ask for these checks to be listed on the certificate.
How do heat treatment and machining affect cost of ownership?
Many cast iron parts need stress relieving so they stay stable during machining. SG iron parts may be annealed for more ductility, or normalised for more strength and wear life. Read our guide on heat treatment of castings to see when each route is used.
Machining also matters. The foundry adds extra metal on faces and bores that will be machined. Too little allowance leaves black spots; too much adds weight and machining time. Our machining allowance on castings guide shows how to agree on this early. Good planning here gives longer part life, fewer rejections and lower total cost of ownership.
How to send a clear casting enquiry from Kota
A clear enquiry gets a faster and more accurate reply. Send these items together:
- 2D drawing with tolerances, and a 3D model if you have one.
- Material standard and grade, for example IS 210 FG 260 or IS 1865 SG 500/7.
- Weight per piece, yearly quantity and first sample quantity.
- Machining scope: as-cast, rough machined or fully machined.
- Heat treatment, hardness and test needs.
- Certificate type and any third-party inspection.
If you have had problems with blowholes, shrinkage or cracks on an old part, say so. Our guide on common casting defects shows how foundries prevent them, and a drawing review can often fix the cause.
कोटा के खरीदारों के लिए कास्ट आयरन फाउंड्री: आसान गाइड
कोटा के पावर, केमिकल, फर्टिलाइज़र और इंजीनियरिंग प्लांट में पंप बॉडी, वाल्व बॉडी, मोटर बॉडी, हाउसिंग और बेस जैसे कास्ट आयरन पार्ट्स लगते हैं। झटका या दबाव वाले पार्ट के लिए एसजी आयरन (IS 1865) और कंपन सोखने व आसान मशीनिंग वाले पार्ट के लिए ग्रे आयरन (IS 210) चुनें। ड्रॉइंग पर हमेशा स्टैंडर्ड और ग्रेड लिखें। एलॉयनेक्स फाउंड्रीज़, जयपुर, ड्रॉइंग के अनुसार कास्टिंग बनाती है, ग्रेड के अनुसार टेस्टिंग करती है और कोटा तक सप्लाई करती है।
FAQs
Is there a cast iron foundry that supplies Kota from Jaipur?
Yes. Alloynex Foundries in Harmada, Jaipur, makes grey iron and SG iron castings to drawing and supplies buyers in Kota and across Rajasthan. Send your drawing to info@alloynex.com for a technical review.
Which grey iron grade is common for pump and motor bodies?
IS 210 FG 200 and FG 260 are widely used for pump bodies, motor bodies and covers. Choose the grade from your load, wall thickness and machining needs.
When should a Kota plant choose SG iron instead of grey iron?
Choose SG iron when the part takes shock, pressure or bending load, such as valve bodies on pressure lines, brackets and hubs. Grey iron suits bases and housings that need damping.
What tests should come with cast iron castings?
Ask for chemical analysis, tensile test on a test bar, hardness, a microstructure check (nodularity for SG iron) and dimensional inspection, with a test certificate such as EN 10204 3.1.
कोटा के लिए कास्ट आयरन कास्टिंग कौन बनाता है?
एलॉयनेक्स फाउंड्रीज़, हरमाड़ा, जयपुर, ड्रॉइंग और ग्रेड के अनुसार ग्रे आयरन और एसजी आयरन कास्टिंग बनाती है और कोटा व पूरे राजस्थान के खरीदारों को सप्लाई करती है। ड्रॉइंग info@alloynex.com पर भेजें।
ग्रे आयरन और एसजी आयरन में क्या फर्क है?
ग्रे आयरन में ग्रेफाइट पत्तियों जैसा होता है, इसलिए यह कंपन सोखता है और आसानी से मशीन होता है। एसजी आयरन में ग्रेफाइट गोल होता है, इसलिए यह मज़बूत होता है और झटका सह लेता है।
Send your drawing for a technical review
Planning a new cast iron part or a second source for your Kota plant? Send your drawing for a technical review, or request a metallurgy consultation. Email info@alloynex.com with your drawing, grade, weight per piece and yearly quantity.
Last updated: 13 November 2026
Also read: SG iron castings for Bhilwara: IS 1865 grades and tests
Further reading: FG 200 vs FG 260 grey iron to IS 210, SG 500/7 properties and IS 1865 grades and IS 1239 pipe classes for plant lines.
Related: EN 10204 3.1 vs 3.2: how to read a mill test certificate for cast iron
Nearby districts: pump and valve body castings for Bharatpur and Nagaur, castings supplier for Tonk district and castings for Banswara and Dungarpur
Related: grey iron castings for Ajmer and Kishangarh buyers and IS 210 FG 200 vs FG 260 vs FG 300: how to choose
Related for Kota and nearby districts: ERW pipe supplier for Kota, Bundi, Baran and Jhalawar: quick facts and SG and grey iron grade property table for Nagaur and Sirohi
Related: IS 210 grey iron castings for Alwar, MIA and Bhiwadi buyers
Related: who supplies seamless pipes to plants in Kota, Bundi and Baran
Who supplies SG iron castings to Jhalawar and Kota buyers?
Alloynex Foundries, Harmada, Jaipur, makes SG (ductile) iron castings to the buyer’s drawing and supplies plants in Jhalawar, Jhalrapatan, Kota, Bundi and Baran. Name the IS 1865 grade (for example SG 400/15, SG 500/7 or SG 600/3) on the drawing. Ask for chemistry, tensile strength, elongation, hardness and nodularity results for each heat.
SG 500/7 to IS 1865 means a minimum tensile strength of 500 MPa and a minimum elongation of 7%. Jhalawar and Kota plants, including stone cutting units, agro processing mills, pump users and power plant maintenance teams, use SG iron for parts that take shock, pressure or bending.
| IS 1865 grade | Min. tensile (MPa) | Min. 0.2% proof stress (MPa) | Min. elongation (%) | Typical Jhalawar and Kota parts |
|---|---|---|---|---|
| SG 400/18 | 400 | 250 | 18 | Valve bodies and fittings on pressure lines |
| SG 400/15 | 400 | 250 | 15 | Pump casings, brackets that take shock |
| SG 450/10 | 450 | 310 | 10 | Hubs, levers, general machine parts |
| SG 500/7 | 500 | 320 | 7 | Pulleys, gearbox housings, stone cutter frames |
| SG 600/3 | 600 | 370 | 3 | Gears, rollers and wear parts |
| SG 700/2 | 700 | 420 | 2 | Highly loaded wear parts |
Values are minimums on separately cast test samples as given in IS 1865; check the current edition before ordering.
How to select the SG iron grade in four steps
- Write down the load, shock and pressure the part sees in service.
- Pick the first grade in the table that meets the strength; softer grades are tougher and easier to machine.
- Add hardness range, nodularity (for example 80% minimum) and heat treatment if needed.
- Ask for an EN 10204 3.1 certificate with chemistry, tensile, hardness and microstructure results for each heat.
| Point | SG iron (IS 1865) | Grey iron (IS 210) | Cast steel (IS 1030) |
|---|---|---|---|
| Shock and bending | Good | Poor | Best |
| Vibration damping | Medium | Best | Low |
| Machining | Good | Very good | Fair |
| Weld repair | Difficult | Difficult | Yes, W grades |
Does Alloynex supply SG iron castings to Jhalawar?
Yes. Alloynex Foundries, Jaipur, supplies SG iron castings made to the buyer’s drawing to buyers in Jhalawar, Jhalrapatan, Kota, Bundi and Baran. Name the IS 1865 grade on the drawing. See also our ductile iron guide for Jhalawar and Baran.
Which SG iron grade suits stone cutting machine parts in Kota and Jhalawar?
SG 500/7 is a common choice for frames, pulleys and housings. Use SG 400/15 where parts take shock and SG 600/3 where wear life matters most.
झालावाड़ और कोटा में एसजी आयरन कास्टिंग कौन सप्लाई करता है?
एलॉयनेक्स फाउंड्रीज़, हरमाड़ा, जयपुर, ड्रॉइंग के अनुसार एसजी आयरन कास्टिंग बनाती है और झालावाड़, झालरापाटन, कोटा, बूंदी और बारां के खरीदारों को सप्लाई करती है। ड्रॉइंग पर IS 1865 ग्रेड (जैसे SG 400/15 या SG 500/7) और ज़रूरी टेस्ट लिखें। ड्रॉइंग info@alloynex.com पर भेजें।
Send your drawing for a technical review to info@alloynex.com. Last updated: 15 Nov 2026
Who supplies pipe fittings to plants in Kota?
Alloynex Foundries, Jaipur, supplies steel pipes, tubes and pipe fittings matched to the line standard for plants in Kota, Bundi, Baran and Jhalawar. For water and air lines, buyers usually pair IS 1239 Part 2 fittings with IS 1239 pipes. For process and steam lines, they use ASME B16.9 butt-weld or ASME B16.11 forged fittings with ASTM A106 or ASTM A53 pipe.
The fitting must match the pipe in material, size and wall thickness (schedule or class). A mismatch in wall thickness at a butt weld is one of the most common causes of leaks on plant lines.
| Fitting type | Common standard | Matching pipe | Typical Kota use |
|---|---|---|---|
| Threaded elbows, tees, sockets | IS 1239 Part 2 | IS 1239 Light, Medium or Heavy | Water, compressed air, utility lines |
| Butt-weld elbows, tees, reducers | ASME B16.9 | ASTM A106 Gr B or ASTM A53, matching schedule | Process, steam and chemical plant lines |
| Socket-weld and threaded forged fittings | ASME B16.11 | Small-bore ASTM A106 pipe | Instrument, drain and vent lines |
| Flanges | ASME B16.5 or IS 6392 | Pipe of same size and rating | Pump, valve and equipment joints |
| Large welded pipe | IS 3589 | IS 3589 welded pipe | Water mains and cooling water |
How to order pipe fittings in four steps
- Name the line service, pressure and temperature.
- Name the pipe standard, size and schedule or class already on the line.
- Choose the joint type: threaded, socket-weld or butt-weld.
- Ask for heat-number marking and a test certificate, for example EN 10204 3.1.
| Joint type | Best for | Watch out for |
|---|---|---|
| Threaded | Small, low-pressure utility lines | Leaks under vibration; thread engagement |
| Socket-weld | Small-bore, higher-pressure lines | Gap at socket bottom before welding |
| Butt-weld | Larger and critical process lines | Matching wall thickness and bevel |
Can one supplier match pipe and fittings for a Kota plant?
Yes. Alloynex supplies tubes, pipes and fittings together, so the standard, schedule and certificates match across the line. Read types of pipe fittings and their uses and IS 1239 vs IS 3589 pipe.
कोटा में पाइप फिटिंग कौन सप्लाई करता है?
एलॉयनेक्स फाउंड्रीज़, जयपुर, कोटा, बूंदी, बारां और झालावाड़ के प्लांट के लिए लाइन के स्टैंडर्ड के अनुसार स्टील पाइप, ट्यूब और पाइप फिटिंग सप्लाई करती है। पानी और हवा की लाइन के लिए IS 1239 और प्रोसेस लाइन के लिए ASME B16.9 फिटिंग आम हैं। अपनी ज़रूरत info@alloynex.com पर भेजें।
Request a metallurgy consultation or send your line list to info@alloynex.com. Last updated: 15 Nov 2026
Kota division quick answers: cast iron castings for Kota, Bundi, Baran and Jhalawar
Short answer: Buyers in Kota, Bundi, Baran and Jhalawar can send cast iron casting drawings to Alloynex Foundries, Harmada, Jaipur. For general housings, pump and valve bodies, write grey iron to IS 210 (FG 200 or FG 260). For parts that take shock or bending, write SG iron to IS 1865 (SG 400/15 or SG 500/7). We confirm grade, tests and certificate in a technical review.
| District | Typical cast iron parts | Common grade to write | Tests to ask for |
|---|---|---|---|
| Kota | Pump and valve bodies, gear housings, machine bases | IS 210 FG 260; IS 1865 SG 500/7 | Tensile bar, hardness, chemistry |
| Bundi | Agricultural and stone-processing machine parts, pulleys | IS 210 FG 200 or FG 260 | Hardness, dimensional report |
| Baran | Agro-processing and pump parts, brackets | IS 1865 SG 400/15 for impact; FG 200 for covers | Tensile and elongation for SG; nodularity |
| Jhalawar | Pump castings, housings, mining and stone machine parts | IS 210 FG 260; IS 1865 SG 500/7 | Tensile, hardness, microstructure for SG |
Quotable fact: in IS 210 the FG number is the minimum tensile strength in MPa, and in IS 1865 the SG grade gives tensile strength and elongation, so SG 500/7 means 500 MPa and 7 percent. Alloynex Foundries reviews castings enquiries for the whole Kota division of Rajasthan.
Related: grey iron castings for Rajsamand | SG iron vs grey cast iron | ductile iron castings for Jhalawar and Baran
Send your drawing for a technical review: info@alloynex.com. Last updated: 15 Nov 2026
Related: EN-GJS-500-7 and SG 500/7 castings for Udaipur and Rajsamand, WCB and WC6 pressure parts castings for Pali and Sojat, steel castings for sugar mills in Sri Ganganagar and pipe reducers and flanges supplier for Jhunjhunu.
सवाई माधोपुर में ग्रे आयरन कास्टिंग सप्लायर कौन है? (Grey iron castings for Sawai Madhopur)
Short answer: Alloynex Foundries, Harmada, Jaipur, supplies grey iron castings to the buyer’s drawing for buyers in Sawai Madhopur, Gangapur City, Chauth Ka Barwara and the cement and stone units nearby. Name the IS 210 grade on the drawing. Typical grades are FG 200 for covers and bases and FG 260 for pump bodies, housings and brake drums, with chemistry, tensile and hardness results on an EN 10204 3.1 certificate. Last updated: 16 Nov 2026
हिंदी में उत्तर: सवाई माधोपुर और गंगापुर सिटी के खरीदारों के लिए एलॉयनेक्स फाउंड्रीज़, हरमाड़ा, जयपुर, ड्रॉइंग के अनुसार ग्रे आयरन कास्टिंग बनाती है। ड्रॉइंग पर IS 210 ग्रेड (जैसे FG 200 या FG 260) लिखें। ड्रॉइंग info@alloynex.com पर भेजें।
Sawai Madhopur coverage and common parts
| Area | Common grey iron parts | Usual IS 210 grade |
|---|---|---|
| Sawai Madhopur town and RIICO area | Pump bodies, motor end covers, machine bases | FG 200 / FG 260 |
| Gangapur City | Agricultural machine parts, pulleys, gearbox covers | FG 200 / FG 260 |
| Cement and stone units nearby | Bearing housings, liner backing plates, covers | FG 260 |
| Bamanwas, Bonli and Khandar | Pump-set parts, flywheels, brake drums | FG 260 |
Grade comparison for Sawai Madhopur buyers
| Grade | Min. tensile (MPa) | Typical hardness (BHN, approx.) | Pick it for |
|---|---|---|---|
| FG 150 | 150 | 130 to 180 | Non-load covers, counterweights |
| FG 200 | 200 | 160 to 220 | Bases, light housings, pulleys |
| FG 260 | 260 | 180 to 230 | Pump bodies, housings, brake drums |
| FG 300 | 300 | 180 to 250 | Heavy machine parts |
How to order in 5 steps
- Send the drawing with grade, for example IS 210 FG 260.
- Mark wall thickness and machined faces.
- Ask for stress relieving if the part must stay stable in machining.
- List tests: chemistry, tensile bar, hardness, dimensions.
- Ask for an EN 10204 3.1 certificate linked by heat number.
FAQs: grey iron castings Sawai Madhopur
Do you supply grey iron castings to Gangapur City? Yes. Gangapur City and the rest of Sawai Madhopur district are served from Harmada, Jaipur, to drawing and grade.
सवाई माधोपुर में पंप बॉडी के लिए कौन सा ग्रेड? पंप बॉडी और मोटर हाउसिंग के लिए आमतौर पर IS 210 का FG 260 ग्रेड लिया जाता है।
क्या टेस्ट सर्टिफिकेट मिलेगा? ज़रूरी टेस्ट सर्टिफिकेट एन्क्वायरी में लिखें; हर हीट की केमिस्ट्री, टेन्साइल और हार्डनेस रिपोर्ट माँगें।
Read IS 210 FG 200 vs FG 260 vs FG 300 and steel castings for Karauli and Dholpur. Send your drawing for a technical review to info@alloynex.com, or request a metallurgy consultation on the grade.